I wrote a cobol code to add record to a file and I runed it using jcl but encounterd an error. The error message is:
´´ procedure IGYWCL was expanded using system library sys1.proclib ´´.
How can i fix this error.
Related
I'm studying the online course from nand2tetris.com through Coursera. When I try to run the nand2tetris CPUEmulator I get the error message 'Illegal character'. Even the simplest program with one command '#0' I get the error message. I tried indenting 0-10 spaces, and I tried the binary version of the command '0000000000000000' and I still get the error message. To run the emulator I'm using a MacBook and I type the command 'CPUEmulator.sh' into the terminal. I'm using TextEdit with Plain Text format. I named the file 'test.hack'. What am I doing wrong?
Syntax error files:
I want to know where I can see the exact error info.There's no hint in vivado.
Thanks!
You can usually check the message tab at the bottom of the screen. Anyhow Vivado is not particularly good at telling you what's wrong with your code (I'm not sure if this has to do with Vivado or parsing HDL in general), so be aware that your error may be "cascading" from an error above in your code than where the message indicates there's something wrong).
For instance, when making the following mistake in line 13:
13 reg [15:0] test_reg_0
14 reg [15:0] test_reg_1;
it will tell you test_reg_1 is not declared and mark it as an error everywhere it's referenced.
I am setting up a new user for liquibase (3.5.3). When we run the following command:
liquibase --defaultsFile=Config /Liquibase.properties --logLevel=Info
We get this error message:
--contexts=initial update Unexpected error running Liquibase: Unknown parameter: '#Liquibase.properties '
SEVERE 2/7/17 11:39 AM: liquibase: Unknown parameter:
'#Liquibase.properties'
liquibase.exception.CommandLineParsingException: Unknown parameter:
'#Liquiba se.properties'
at liquibase.integration.commandline.Main.parsePropertiesFile(Main.java:
476)
at liquibase.integration.commandline.Main.run(Main.java:164)
at liquibase.integration.commandline.Main.main(Main.java:103)
For more information, use the --logLevel flag
I thought there may have been a funny character in the file, so we recreated it, but still received the same error. We also, took a working copy of a properties file from another project and modified it. This also produced the same result.
Any ideas on what is going wrong or thoughts on how to fix it, would be greatly appreciated.
m
 is a UTF-8 Byte order mark (or short BOM). Some text editors write one by default when using UTF-8 encoding, even though, most programs do not understand it.
In your case, liquibase seems to be one of the programs which do not understand the BOM and treat it as the beginning of a parameter. To fix this, make sure you save the file as UTF-8 without BOM if your editor supports this option, or alternatively, as ASCII or ISO 8859 (ANSI) if you only use characters defined in ASCII.
A typical Pig error that occurs without much usefull information is the following:
Job in state DEFINE instead of RUNNING
Often found in a line like this:
Caused by: java.lang.IllegalStateException: Job in state DEFINE instead of RUNNING
I have seen some examples of this error, but would like to have the generic solution for this problem.
So far, at each occasion where I have encountered this error, it is because Pig fails to load files. The error in the question is printed to stderr log, and you will not find anything usefull there.
However, if you were to look in the stdout log, you would expect to find the following:
Message: org.apache.pig.backend.executionengine.ExecException: ERROR 2118: Input Pattern hdfs://x.x.x.x:x/locationOnHDFS/* matches 0 files
Typically followed by:
Caused by: org.apache.hadoop.mapreduce.lib.input.InvalidInputException: Input Pattern hdfs://x.x.x.x:x/locationOnHDFS/* matches 0 files
At this point the most likely suspects are:
There are no files in the specified folder (though the folder exists)
The user that is running the script does not have the rights to access the relevant files
All files are empty (not sure about this one)
Note that it is a commonly known difficulty that pig will error out if you try to read an empty directory (rather than just processing the alias with 0 lines).
I am trying to execute "db2look" command from within Excel using VB. But I'm getting Run-time Error
An unexpected token "db2look" was found following "BEGIN-OF-STATEMENT". Expected tokens include: "DECLARE". SQLSTATE=42601
I know connection and everything is fine, as I am able to run simple select queries and based on error it's not connection issue but rather like "db2look" not recognized or valid. I've ran same exact command in cmd window at it works fine.
Just wondering if anyone has been able to run the "db2look" command outside of db2 command window/editor and using VB/Excel? Or if there is something that I am missing.
Thanks
db2look is a tool and standalone executable which cannot be run like a regular SQL statement. It needs to be run from the command line (shell).