I have an FTDI converter from USB to RS485 which uses the FT232RL chip, when I plug it to my computer it gets detected normally and no problems|
When I try to connect it to my laptop it gets powered up, after a bit it gets detected and then after one second it gets disconnected again and it will be detected after a minute or so and will disconnect again and this will keep happening
I have the VCP and the D2XX drivers both on my laptop and on my computer but the problem only exists on my laptop
I have verified that the converter is a genuine FTDI device
I also tried download USBDview and uninstalling the device but the same things keeps happening
What should I do?
Thanks in advance
Related
Working with the STM32L062 Cortex-M0 and CubeMX the generated USB CDC-ACM code works fine in Windows. With loopback code running on the STM32 and TerraTerm running on Windows characters typed in the terminal window correctly echo back. However, when this same system is then plugged into a laptop running Ubuntu, the device fails to enumerate. Even worse, the system doesn't appear to respond to the connection whatsoever- no new messages appear via dmesg that even a failed enumeration is going on. Given that the code used is generated by CubeMX wizards it is difficult to know what to start to troubleshoot. Any suggestions?
As an aside, this isn't the first issue presented by CDC-ACM drivers. Implementing a USB CDC-ACM stack for a PIC32MM processor, data can be sent to the host but not received from the host, however, if the driver is switched to plain vanilla CDC then data can be sent both ways no problem. So it seems maybe Ubuntu has some issues with the default USB drivers, but either way, it's very odd that the ST driver gets zero response at all from the system.
I have a project based on a Nucleo H743ZI2 board that communicates with a PC through the USB OTG port on the Nucleo.
Everything is working fine as long as, weirdly enough, I have the STlink USB cabled plugged in (which I have been using to work on the firmware, flash, debug, etc).
However, today I was getting ready to do actual tests with this project and used an external power source to power the H7. I initially tried a 3.3V external source which is available from one of the shields, and then tested a lab PSU at both 3.3V. Thinking it could be PSU related I also tried external 5V with the same results.
Basically, the device is not recognized by the computer operating system, unless the STlink USB is plugged in.
I can't really put my finger on this one; I initially thought it was a PSU related issue (that nucleo board has some restrictions when it comes to using external power sources) but at this point I am fairly confident I am failing to initialize something in my code. Not sure what though.
I'd be happy to share with my code, but wouldn't know where the start. I haven't done much as far as the USB OTG is concerned other than modifying the receive callback to process the data.
Any idea what I might be missing here?
Cheers
I made a STM32F042k6, battery powered device, that I would to flash vi DFU protocol.
In order to do so I disconnect the battery, I pull BOOT0 to VCC, and then plug the device in USB3 port of PC (no USB2 available). The device is not recognized and showed
VID:0000 PID:0002 (case I)
However, when I first connect battery, and then connect the device to PC it is recognized without a fuss (case II).
The problem I face is that I would like to initiate jump to bootloader program by command in software - but then I reach exactly the same condition as in case I.
Could you help me to identify what conditions for proper boot I am violating?
EDIT:
The way I have discovered the problem was when I implemented software jump to bootloader. It seemed not to work at all (VCP device dissapeared, and erroreous <> device appeard in system PID:0002 VID:0000).
I wanted to enter bootloader by pulling up BOOT0 pin, but I could see that I sucseed only when battery-power cycled. USB power cyccle resulted in the same "failed descriptor" device.
I suspect that when powered on via USB, the booloader has som ecommunication problems and cannot establish proper PID and VID. When powered via battery - this problem is not existing.
Do you have a discovery board?
I read in the STM32F042x4/x6 Reference Manual (DocID025832 Rev 5):
The STM32F042x4/x6 embeds a full-speed USB device peripheral compliant
with the USB specification version 2.0.
(part 3.19, p.27).
In the AN2606 (Rev 33), a table shows the USB configuration which is used by the DFU Bottolader in USB FS (Full-speed):
I assume that the USB in the bootloader is the 2.0, but USB 3.0 must be USB 2.0 compliant. So it is possible to use an USB 3.0 port.
I suggest you use the DfUSe Demo from ST. Its interface consists of a tab where the DFU devices available are displayed when detected. I try it on another STM32x by following these steps:
Open DfuSe Demo software.
Plug BOOT0 to Vdd to put the micro on DFU mode.
Plug the USER USB to your computer port.
The name of your device should appear in “Available DFU Devices” field.
You could try to use directly PA11 and PA12 as well (according to Table 12) instead of the USB port of your board.
EDIT:
Another solution to upgrade your firmware without driving boot0 is to jump directly into the DFU bootloader of ST inside your firmware. Else you could design your own IAP bootloader (In-Application Programming).
I hope that helps.
I faced this same issue with the STM32 Mini F401 and dug into it for several days. Unlike the OP I was unable to find any electrical conditions which reliably got the bootloader to do the right thing. I was able to program my board maybe once every 20 tries, which was really slowing down my process.
In the end I discovered that I can go to the Windows device manager, show hidden devices, and there will be an entry in Universal Serial Bus Devices called STM32 BOOTLOADER. When the issue is happening the board is connected in dfu mode but that device is not marked active in the device manager.
To resolve the issue consistently, you can manually delete the hidden STM32 BOOTLOADER entry, uninstalling the device (no need to delete the driver, just uninstall the device). Then reboot your board in DFU mode and it should connect as expected every time. Unfortunately I need to do this process every time I want to program, but that's far better than the inconsistent/intermittent failures before.
First of all, there's a similar thread on OpenQNX posted years ago but the solutions don't really apply for me.
Having said that, I want to create an OS image of QNX 6.6.0 to put on a Compact Flash card. This card is plugged in an USB adapter which is connected to my host pc. I'm running Neutrino in a VM (VMware/VirtualBox) for which I enabled USB support. Generally, the adapter works fine under Win (current host) and Linux.
The (apparently out-dated) tutorial I was following stated to search for devices named umass* or hd* after connecting the USB adapter. But there aren't any (except for hd0).
See also "ls /dev" screenshot.
The processes devb-umass and io-usb are running. So I expect that the adapter is detected automatically.
Any suggestions what went wrong?
OK, it seems that I had to restart the usb driver 'devb-umass' (several times). When the card reader is already plugged-in during the booting the driver will not detect it autoamtically. Thus one has to unplug and plug it in again after the devb-umass was getting re-started. It also might have been that the Host Controller Driver (HCD) was set to 'ohci' instead of 'ehci'.
Everything is working now as expected.
(Thanks Tim from the OpenQNX forum! ;) )
I'm trying to connect a usb sensor (see Toradex) to an android phone (Desire Z) running android 4.0.3.
To test this, I wrote a small app to enumerate the attached device(s).
This supposed to have USB HOST mode implemented and to power the usb sensor (HID)... but it doesn't.
I got a USB OTG cable and now, when I attach the cable, a small icon appears in the status bar (car mode).
I'm disappointed since I waited for this feature for awhile now...
Any thoughts? I read almost everything out there related to this (Sven work and whatnot) but I might have missed something...
Thanks!
I have worked a lot in the past year and a half to build custom android platform. Some was under Froyo but mostly on Gingerbread. Most on the hardware I added was on either a UART or on USB, which is what you want to do. Unfortunately, it is not as easy to add a USB peripheral on an Android device than on a PC or a MAC. PCs and MACs have virtually unlimited memory space (hard drive). They can hold the drivers of a very large number of devices. That makes it possible to do auto-detection and automatic loading of drivers. On an Android device, it is a lot more lean therefor, just the required drivers are stored on the device. Every time I added a new device, I had to compile the driver for my platform and make some modification in my configuration. It is also possible to load the driver as a module instead of compiling it with the kernel (gives a file.ko output). Although, the driver must have been written accordingly. But, you will have to install it by modifying the "init.rc" which requires root privilege.
here is a few link of question/answer about about drivers in Android. That should give you a little bit more info:
USB touchscreen driver
Hope it helps but unfortunately, it is quiet a lot of work do do.