I'm trying to get used to the Modelica.Fluid.Dissipation. I want to evaluate the heat transfer coefficient of a straight pipe using the function kc_overall. I tried to followthe UsersGuide example. I'm not sure I understood how to write it and which inputs I have to use. Here's my code:
model Heat_tranfer_calcul
Modelica.SIunits.MassFlowRate M_FLOW=0.3 "input mass flow rate";
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall_IN_con IN_con(d_hyd=13e-3,L=15);
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall_IN_var IN_var(cp=4184,eta=8.9e-4,lambda=0.6,rho=1000) ;
equation
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall(IN_con,IN_var,M_FLOW)
end Heat_tranfer_calcul;
I also tried to get the fluid properties directly from the Modelica.Media.Water.StandardWater.
If someone could help me to uderstand how the function works that would be really helpful.
Maxime
The function kc_overall only takes two arguments — the records IN_con and IN_var. The mass flow rate must be specified through IN_var so your code should be:
model Heat_tranfer_calcul
Modelica.SIunits.MassFlowRate M_FLOW=0.3 "input mass flow rate";
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall_IN_con IN_con(d_hyd=13e-3,L=15);
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall_IN_var IN_var(cp=4184,eta=8.9e-4,lambda=0.6,rho=1000, m_flow=M_FLOW);
equation
Modelica.Fluid.Dissipation.HeatTransfer.StraightPipe.kc_overall(IN_con,IN_var);
end Heat_tranfer_calcul;
By the way, it is good Modelica coding practice to use lowercase letters for variable names, that is m_flow instead of M_FLOW.
Related
I have a doubt about the functionment of the Modelica.Fluid.Dissipation.HeatTransfer.HelicalPipe function.
I want to model an helical heat exchanger using the DynamicPipe of the Modelica Standard Library. Does the function allow me to specify such a geometry in order to simulate it with my boundary conditions ? Or does the function just return the heat transfer coefficient with geometry parameters in inputs ? If that's the case is it possible to simulate a flow in a pipe which is helical without using the Bends of the Modelica Standard Library ?
Thanks for your responses and have a good day,
Maxime
I am new to LabVIEW and I am trying to read a code written in LabVIEW. The block diagram is this:
This is the program to input x and y functions into the voltage input. It is meant to give an input voltage in different forms (sine, heartshape , etc.) into the fast-steering mirror or galvano mirror x and y axises.
x and y function controls are for inputting a formula for a function, and then we use "evaluation single value" function to input into a daq assistant.
I understand that { 2*(|-Mpi|)/N }*i + -Mpi*pi goes into the x value. However, I dont understand why we use this kind of formula. Why we need to assign a negative value and then do the absolute value of -M*pi. Also, I don`t understand why we need to divide to N and then multiply by i. And finally, why need to add -Mpi again? If you provide any hints about this I would really appreciate it.
This is just a complicated way to write the code/formula. Given what the code looks like (unnecessary wire bends, duplicate loop-input-tunnels, hidden wires, unnecessary coercion dots, failure to use appropriate built-in 'negate' function) not much care has been given in writing it. So while it probably yields the correct results you should not expect it to do so in the most readable way.
To answer you specific questions:
Why we need to assign a negative value and then do the absolute value
We don't. We can just move the negation immediately before the last addition or change that to a subtraction:
{ 2*(|Mpi|)/N }*i - Mpi*pi
And as #yair pointed out: We are not assigning a value here, we are basically flipping the sign of whatever value the user entered.
Why we need to divide to N and then multiply by i
This gives you a fraction between 0 and 1, no matter how many steps you do in your for-loop. Think of N as a sampling rate. I.e. your mirrors will always do the same movement, but a larger N just produces more steps in between.
Why need to add -Mpi again
I would strongly assume this is some kind of quick-and-dirty workaround for a bug that has not been fixed properly. Looking at the code it seems this +Mpi*pi has been added later on in the development process. And while I don't know what the expected values are I would believe that multiplying only one of the summands by Pi is probably wrong.
I've been working on the HM reference software for a while, to improve something in the intra prediction part. Now a new intra prediction algorithm is added to the code and I let the encoder choose between my algorithm and the default algorithm of HM (according to the RDCost of course).
What I need now, is to signal a flag for each PU, so that the decoder will be able to perform the same algorithm as the encoder decides in the rate distortion loop.
I want to know what exactly should I do to properly add this one bit flag to the stream, without breaking anything in the code.
Assuming that I want to use a CABAC context model to keep the track of my flag's statistics, what else should I do:
adding a new context model like ContextModel3DBuffer m_cCUIntraAlgorithmSCModel to the TEncSbac.h file.
properly initializing the model (both at encoder and decoder side) by looking at how the HM initialezes other context models.
calling the function m_pcBinIf->encodeBin(myFlag, cCUIntraAlgorithmSCModel) and m_pcTDecBinIfdecodeBin(myFlag, cCUIntraAlgorithmSCModel) at the encoder side and decoder side, respectively.
I take these three steps but apparently it breaks something.
PS: Even an equiprobable signaling (i.e. without using CABAC contexts) will be useful. I just want to send this flag peacefully!
Thanks in advance.
I could solve this problem finally. It was a bug in the CABAC context initialization.
But I want to share this experience as many people may want to do the same thing.
The three steps that I explained are essentially necessary to add a new syntax element, but one might be very careful with the followings:
In the beginning, you need to decide either you want to use a separate context model for your syntax element? Or you want to use an existing one? In case of CABAC separation, you should define a ContextModel3DBuffer and the best way to do that is: finding a similar syntax element in the code; then duplicating its ``ContextModel3DBuffer'' definition and ALL of its occurences in the code. This way assures that you are considering everything.
Encoding of each syntax elements happens in two different places: first, in the RDO loop to make a "decision", and second, during the actual encoding phase and when the decisions are being encoded (e.g. encodeCtu function).
The order of encoding/decoding syntaxt elements should be the same at the encoder/decoder sides. For example if your new syntax element is encoded after splitFlag and before predMode at the encoder side, you should decode it exactly between splitFlag and predMode at the decoder side.
The context model is implemented as a 3D matrix in order to let track the statistics of syntaxt elements separately for different block sizes, componenets etc. This means that when you want to call the function encodeBin, you may make sure that a correct index is being used. I've made stupid mistakes in this part!
Apart from the above remarks, I found a the function getState very useful for debugging. This function returns the state of your CABAC context model in an arbitrary place of the code when you have access to it. It is very useful to compare the state at the same place of the encoder and the decoder when you have a mismatch. For example, it happens a lot that you encode a 1 but you decode a 0. In this case, you need to check the state of your CABAC context before encoding and decoding. They should be the same. If they are not the same, track back the error to find the first place of mismatch.
I hope it was helpful.
I have written a finite volume model. The parameter n represents the number of volumes. After translating, the parameter can't be modified. Dymola gives this message:
Warning: Setting n has no effect in model.
After translation you can only set literal start-values and non-evaluated parameters.
I think the problem is that the parameter n is used in the equation section. There I use the following code:
equation
...
for i in 2:n-1 loop
T[i] = some equation
end for
I also use n for the calculation of the initial values of T.
The purpose is to make a script that repeatedly executes the model but with a different n.
How can I do this?
The issue here is that your parameter n affects the number of variables in the problem. Dymola (and all other Modelica compilers I know of) evaluate such parameters at compile time. In other words, they hard code the value at compile time into the model.
One potential workaround in your case is to perform the translation or simulation inside your loop. Note that in the translate and simulate commands in Dymola you can include modifications. Just add them after the model name. For example MyModel would become MyModel(n=10).
The only effect AudioUnit on iOS is the "iTunes EQ", which only lets you use EQ pre-sets. I would like to use a customized eq in my audio graph
I came across this question on the subject and saw an answer suggesting using this DSP code in the render callback. This looks promising and people seem to be using this effectively on various platforms. However, my implementation has a ton of noise even with a flat eq.
Here's my 20 line integration into the "MixerHostAudio" class of Apple's "MixerHost" example application (all in one commit):
https://github.com/tassock/mixerhost/commit/4b8b87028bfffe352ed67609f747858059a3e89b
Any ideas on how I could get this working? Any other strategies for integrating an EQ?
Edit: Here's an example of the distortion I'm experiencing (with the eq flat):
http://www.youtube.com/watch?v=W_6JaNUvUjA
In the code in EQ3Band.c, the filter coefficients are used without being initialized. The init_3band_state method initialize just the gains and frequencies, but the coefficients themselves - es->f1p0 etc. are not initialized, and therefore contain some garbage values. That might be the reason for the bad output.
This code seems wrong in more then one way.
A digital filter is normally represented by the filter coefficients, which are constant, the filter inner state history (since in most cases the output depends on history) and the filter topology, which is the arithmetic used to calculate the output given the input and the filter (coeffs + state history). In most cases, and of course when filtering audio data, you expect to get 0's at the output if you feed 0's to the input.
The problems in the code you linked to:
The filter coefficients are changed in each call to the processing method:
es->f1p0 += (es->lf * (sample - es->f1p0)) + vsa;
The input sample is usually multiplied by the filter coefficients, not added to them. It doesn't make any physical sense - the sample and the filter coeffs don't even have the same physical units.
If you feed in 0's, you do not get 0's at the output, just some values which do not make any sense.
I suggest you look for another code - the other option is debugging it, and it would be harder.
In addition, you'd benefit from reading about digital filters:
http://en.wikipedia.org/wiki/Digital_filter
https://ccrma.stanford.edu/~jos/filters/