How to restrict textbox to take/type input 0~100 percentage only in angular 10? it should not take input greater than 100
Related
I am using Robot-framework selenium2.0.
In the robot test I made, it fills out a form and save it. In the form, I have to put some numeric values in some text boxes but somehow the previous\default value of 0.0 is not removed from any of the box. When I run the test normally it puts the values after 0.0. For example I want to put 50 in the box but the test puts 50 after 0.0 so it becomes 0.050 and when it switches to next text box the value becomes NaN.
Here is how I am doing it,
wait until element is visible text_field
click element text_field
input text text_field 50
Is there any ascii codes that can be used to select values (ctrl+a) and delete the values first and then use input text to input values?
You can try:
Clear Element Text text_field
More on this here.
You could also use Selenium directly:
driver.findElement(By.id("text_field")).clear();
This may be work for you:
driver.findElement(By.id("text_field")).click()
driver.findElement(By.id("text_field")).pressKey('Ctrl' + 'A')
driver.findElement(By.id("text_field")).pressKey('Delete')
more Press Key here
how can i get the percentage of an element depending on the whole layout? I tried to change the rulers to percent but the values are not accurate (859%, 1100%...).
1.Change to procent,
2.view info panel F8
3. select to layer with the object.
4. cmd+t or ctrl+t now you se the element with and height with 1 decimal.
My dashboard consist of 10 sub-reports. And some of those sub-reports are several pages.In a page footer of a dashboard I entered expression in a textbox:
="Page " & Globals!OverallPageNumber & " of " & Globals!OverallTotalPages
which gives me the page number, but how can I move this to the right corner?
As you can see on a below picture the expression already further right than even sub-report itself. What else can I do?
This is my report properties for the Dashboard:
It looks like the table you have is a Matrix with Column grouping. The grouping is expanding and pushing the width but unfortunately, that doesn't push the footer out.
Since you can't make the position dynamic, you'll have to figure out where the sub report page ends and extend the main report's width to fit the page number.
It looks like the first column is 4 inches wide and the matrix columns are 2 inches wide. I would put the text box at 15 inches and make it 1 inch wide.
i want to write a mechanical eng. software to calculate kitchen hood exhaust flow rate and make a report.
firstly, user will check the calculate button, secondly user will check gas or electric and then user will enter the area.
for example, user select two random types(there are 40 types of kitchen hoods) and selects gas and enters areas. i will make calculation from these selections but my problem is: i can't write them to second form with sorting the selected ones.
you can see label 1, label2 etc. i can send the selected box text to labels with if statement:
If CheckBox1.Checked Then
Form2.Label1.Text = Label5.Text
End If
but i don't know which one will selected and i will have 40 types but in report part (form2) i will have maximum 10 types(because of the general layout of kitchen designs). so i want to sort selected ones and add report form without any blank rows.
i'm really sorry for my poor English.
I am trying to control the length of the text box. The property of the textbox only has maxlength tool. If I want to set minimum length for textbox to be 3, how can I proceed this?
I want an error to pop up when someone types 10 instead of 100. User can only put a combination of 1 and 0 like 100,000,010,001, etc. Type of these are double.(not string)
handle the Textbox control validating event. See this