I need to launch a script on a Raspberry Pi from my OVH web site.
The Raspberry Pi is behind a modem and I redirected port 22 to the Raspberry Pi local address. If I try to connect with the modem public IP (eg 91.XX.YY.ZZ) from a computer on the LAN it works as expected : ssh pi#91.XX.YY.ZZ works.
However if I try to do the same command from the OVH shared server (I ssh from my computer to OVH server, and when connected type the command above), I get ssh: connect to host 91.XX.YY.ZZ port 22: Connection refused although I set up temporarily the Raspberry Pi to allow PasswordAuthentication yes (and rebooted it). I would expect to be prompted for password when ssh-ing from the OVH host.
So now I fear ssh request emitted from OVH server may be blocked by OVH (as ping is for example), but would it give such connection refused message, and how can I test it ? Otherwise what did I do wrong ?
Any help greatly appreciated!
After a bunch of research with other key words (php ssh2_connect OVH) it seems that it is not possible do ssh FROM OVH shared-hosting. Here is a discussion from 2019 (in French).
Related
I would like to connect the remote machine to my local VPN and then ssh to that remote machine from the other machines in my local network.
Is this possible? Will the remote machine get new IP which will be visible in my local network? Do I need to configure anything manually?
I'm using FortiClient for VPN.
Yes this is absolutely possible. Try Following steps
1-Deploy VPN and assign the ipranges in DHCP public or private
2-Make Sure to turn off the firewall for vpn server for now
3-Turn off the Clients Firewall
4-Connect to VPN
5-If your connection loose try to see the client's IP from server
side and try to take SSH
6-Take ssh from your server
7- Ping the server from other local machines
8-Then enable the server side firewall and see the effect if ssh is
still possible if not make a rule for specific port for ssh
I'm developing some webhook required direct access public domain to internal machine, thinking use SSH tunnel to forward data, or got alternative solution?
Hosting server & development machine are in same network
192.168.1.2/24 (Hosting server)
2nd machine is virtual mapping using forticlient firewall without static or dynamic IP in visible in hosting server, so is 1 way initial communication right now.
In this case possible to setup SSH tunnel forward all traffic from 192.168.1.2:80 to handle in development machine port 8080?
How to ssh syntax look like?
Thanks.
This could be done by setting up an SSH tunnel to the remote machine:
ssh -L localhost:80:localhost:8080 development-system
Every request to port 80 on the hosting-server is now forwarded to port 8080 on the development-system.
Please note, that the port 80 on the hosting-server could only be used, when you start the SSH command as root. Also note that the port 80 is only accessible from the hosting-server. To access the port 80 on the hosting-server from everywhere use the following:
ssh -L 80:localhost:8080 development-system
Be sure that you want that.
A good introduction to the topic could be found at
https://www.ssh.com/ssh/tunneling/example
https://unix.stackexchange.com/questions/115897/whats-ssh-port-forwarding-and-whats-the-difference-between-ssh-local-and-remot
Okay, here's the situation I am in. I have a raspberry Pi 2 model B. I have Raspbain Jessie installed as the OS. I have Apache installed as well. I have a web server running and i am able to edit it and access the site from different devices on different internet connections. I want to be able to connect to my RaspPi through SSH on my MacBook Pro. I am able to do this while on the same network. My Pi is plugged into the router via an Ethernet. What i have tried is, logging into my router and reserving an IP for my Pi, i also entered my MAC address here. I have gone into the port forwarding options in my router and have it set up as: HTTP, TCP, Server address(the one i reserved) my Ipv6, and Start port 80, end port 80. Ontop of that i have gone into my /etc/dhcpcd.conf file. There at the end of the file i added
interface eth0
static ip_address=10.0.0.100
static routers=10.0.0.1
static domain_name_servers=68.44.180.118 2001:558:feed::1 2001:558:feed::2
The guide I followed is attached here and follows other guides i have seen.
http://www.circuitbasics.com/how-to-set-up-a-static-ip-on-the-raspberry-pi/
Yet when i try to SSH remotely i cannot get a connection, and when i connect on the same internet i can connect as normal. Please if anybody sees what could help .
Your router's firewall is probably blocking the ports for SSH, which does not use port 80 (in raspbian, I think its default is port 22). If you are going to take the risk of leaving your SSH open to the public, you should probably switch it to a different port other than the default before opening up a port on your firewall. The Raspbian Community has a thread on how to properly change SSH's default server port. You'll also need to make sure your SSH client is using the same port. You will need to leave 80 open for web, and also forward the SSH port, which ever you choose that to be (22 is the default).
I want to connect to a remote server (host1) that accessible only from it's private network.
Another server (host2) is accessible from the Internet.
I opened a tunnel to host2 using PuTTY and tested it's working with Firefox (also checked that I got different IP address).
How can I connect to host1 using the tunnel I created?
I tried to configure proxy (to the tunnel I created - localhost) in PuTTY but it's not working.
The error I got: "Server unexpectedly closed network connection"
Pay attention that the host is the computer name in the network.
You connect to the local tunnel end directly, no "proxy" setting is needed.
This typically means that you use "localhost" as a Host Name. And a port according to your tunnel configuration.
See my guide for tunneling SFTP/SCP session. It's for WinSCP, but just use PuTTY instead of WinSCP in section Connecting through the tunnel.
I want to connect to remote amazon aws service(EC2 instance) , and I would like to be able to ssh to it from my laptop while using the campus provided network (which has cyberoam firewall). However, they have pretty much every port blocked and ssh won't work. Is there anything i can do? does ssh run through port 80? I don't really know what to do .
All it says is :
ssh_exchange_identification: read: Software caused connection abort
ssh works elsewhere.
You can set your SSH server to use port 80 (or 443 if 80 is used for a webserver). Just check the configuration file of your ssh server for more details!