The broadcast stops working 5 seconds after the start. All ports are open. Why can this error still occur?
If you run Ant Media Server on Ubuntu virtual machine on Windows host and run browser (as WebRTC peer) on host (Windows) side, then you can encounter with such a problem.
As a solution, you can start browser on virtual machine side. Or better run AMS on a real machine or VPS.
Related
The Issue: I have disabled SELinux entirely. We have Apache running on a CentOS 8 VM. We have a simple information page running on the server. It displays great when we are on that VM in Gnome using either 127.0.0.1, locahost, or it's actual IP address. However, we cannot view this page from the same subnet or any subnet. The message we get in our browsers when off that server is "server took too long to respond". I am thinking there is some small little thing we must be missing in the Apache config. We even have Webmin on there to make the administration easier. I have never had this problem with CentOS 5/6/7 previously. I know that CentOS 8 is the last release as RHEL has bought it, and they want to see CentOS killed off.
Actions Taken:
Disabled SE Linux entirely to eliminate it being a firewall issue.
Installed Webmin to have access to the Apache administration module making looking for any issue easier.
Tested from the server itself in Gnome which the page comes up.
Tested from other computers on the same subnet, off the same switch.
Tested from other subnet computers.
I am planning on using VS Code to work out of WSL2 installed on a remote machine. Before doing that, I wanted to check the direct connectivity from a Windows 10. I followed the instructions given in this blog. Also, the remote Windows 10 is on a VPN.
When I use the command ssh <username>#<IP address>, I get the message
kex_exchange_identification: read: Connection reset
Is there anything I am missing to get the connection going?
I want to test my website on edge and internet explorer so I tried using a windows VM, I am currently on linux mint 19.1, I start the gohugo server with "hugo server --disableFastRender" and create the VM in virtualbox using bridged adapter but I cant load localhost:1313 on the vm.
I tried using NAT and port forwarding but I have the same results, also tried the conection between the host and VM using ping and the VM can reach the host but the host cant connect to the VM so I guess that the problem is there but I dont know what to do now. The place where I am working uses IPv6 and I never worked with it before so maybe it has something to do with that
Start your site as usual with hugo server, which makes it available at http://localhost:1313
Leave your Windows VM network settings at their defaults
In your Windows VM, navigate to http://10.0.2.2:1313 to hit your hugo site
In a nutshell, 10.0.2.2 on your Windows VM (its default gateway) is equivalent to localhost on your linux host.
You can get the default gateway of your Windows VM by running ipconfig in Command Prompt.
I am running FreeNAS 11.1-U5 at home. I have everything configured and have created VM's for Windows Server, Ubuntu, pfSense, FreePBX. I was able to install Windows and Ubuntu, but shortly after (a few hours after installing them), and after turning them off through the FreeNAS GUI, they have stopped turning on. FreeNAS reports at the top of the GUI that the start was successful, but the VM details still read "stopped".
I have run the VM's before and have the required settings in my CMOS configured for the Host (FreeNAS machine). Restarting the host will fix the problem for a while and it will let me work with the VM's, but I cannot keep restarting FreeNAS. Can anyone tell me why this happens and how to fix it please?
I run Debian linux.
I want to make a virtual machine in virtualbox, wich boots from a server via drbl.
The server will be my laptop.
The virtual machine start booting, but fall into infifite boot-loop.
It load one part of the OS from the server, then stop loading, start it again...
Have anyone seen this error?