I am working on Android Studio. The "build" tab says there are six errors but all it prints are the following:
error: Cannot figure out how to save this field into database. You can consider adding a type converter for it.
error: Cannot find getter for field.
error: Cannot find setter for field.
error: Cannot figure out how to read this field from a cursor.
error: Cannot find getter for field.
error: Cannot find setter for field.
There is not much here that is useful to me because I have multiple Entities and DAOs. How do I get access to the actual line numbers causing trouble?
Related
I'm writing the following nested function where dfsVisit uses the arrays "numCaminos" and "colores" declared in the outer function
However the kotlin compiler is giving me a "variable expected" error on the assignments in lines 31 and 34 specifically, this error doesn't show up on any of the other Array assignments within the nested dfsVisit function. I tried de-nesting the functions and passing the arrays as arguments of dfsVisit but the problem persisted on those 2 assignments specifically. Why could this be happening?
I'm running the Kotlin compiler in Manjaro Linux through the repository package
Note: Sorry for using a picture instead of a code block, the post editor was giving me some formatting issues.
Just remove !! from the left side of the assignment. It doesn't really make sense there.
I erroneously deleted the ‘footer.liquid’ file in the Providence theme.
I am unable unable to create a new footer.liquid file in sections as I am getting the error below:
“New schema is incompatible with the current setting value. Invalid type value for block '1523601164583'. Type must be defined in schema. New schema is incompatible with the current setting value. Invalid type value for block '1523858388687'. Type must be defined in schema.New schema is incompatible with the current setting value. Invalid type value for block '1523592394611'. Type must be defined in schema.New schema is incompatible with the current setting value. Invalid type value for block '1523858779593'. Type must be defined in schema”
Any ideas?
I know its been a while but in case anyone ends up on this thread looking for the same thing or the poster of the question did not find a fix (probably not the case) up to this point, I will attempt to answer with how I got around this.
First of all lets examine why this happens, from my understanding, each time we add or modify certain values inside a section schema, the settings_data.json located in the config folder, will have settings generated inside of it upon usage of that section.
So when we go back into the section and change for example the type of a block, it will no longer match the existing settings inside of the settings_data.json and as such you will get an error back.
So how do if fix it? We simply go into the Shopify Store Adimin and remove the blocks that make use of the type we've changed, after we do this we can easily define any new type we want, add the blocks back and we will no longer receive an error.
I am trying to call one of the 2 modules (fifo_test_1 or fifo_test_2) depending on the value of bit data[0] in the following Verilog code.
module VC_selector(data);
input [10:0] data;
always # (data[0])
begin
if(~data[0])
begin
fifo_test_1 t1(.buf_in(data));
end
else if (data[0])
begin
fifo_test_2 t2 (.buf_in(data));
end
end
endmodule
fifo_test_1 and fifo_test_2 modules are working fine. But the above code gives these errors:
** Error: C:/Users/Swayam/Documents/VC_selector.v(8): Undefined variable: fifo_test_1.
** Error: C:/Users/Swayam/Documents/VC_selector.v(8): near "t1": syntax error, unexpected IDENTIFIER
** Error: C:/Users/Swayam/Documents/VC_selector.v(12): Undefined variable: fifo_test_2.
** Error: C:/Users/Swayam/Documents/VC_selector.v(12): near "t2": syntax error, unexpected IDENTIFIER
Please help me debug the code.
You cannot change the modules included while the hardware is running. The modules must be a constant during execution. For that reason, you can't include a module definition inside an always statement.
One thing you could do is move the two modules outside the always block and use some logic to switch between their outputs. Because neither of the fifo modules have outputs that would be rather difficult to do in this particular case, but it is possible in the general case.
assign my_switched_output = data[0] ? module_1_output : module_2_output;
The ternary operator (used here) allows you to do this switching that it appears you are attempting to do.
Another thing to make sure you have done is to include both the module file you are trying to simulate/synthesize AND all of the submodule verilog files you need in the command. How to include all of these files based on the simulator.
I get the following compilation error in Monodevelop:
Error CS0121: The call is ambiguous between the following methods or properties:
'System.Linq.Enumerable.ToArray<AudioBitrateCalculationStream>(this System.Collections.Generic.IEnumerable<AudioBitrateCalculationStream>)' and
'System.Linq.Enumerable.ToArray<AudioBitrateCalculationStream>(this System.Collections.Generic.IEnumerable<AudioBitrateCalculationStream>)' (CS0121)
Both definitions are exactly the same. I cannot understand what the issue is. Internet search does not help.
i'm talking to a COM object (Microsoft ADO Recordset object). In a certain case the recordset will return a failed (i.e. negative) HRESULT, with the message:
Item cannot be found in the collection
corresponding to the requested name or
ordinal
i know what this error message means, know why it happened, and i how to fix it. But i know these things because i read the message, which fortunately was in a language i understand.
Now i would like to handle this exception specially. The COM object threw an HRESULT of
0x800A0CC1
In an ideal world Microsoft would have documented what errors can be returned when i try to access:
records.Fields.Items( index )
with an invalid index. But they do not; they most they say is that an error can occur, i.e.:
If Item cannot find an object in the
collection corresponding to the Index
argument, an error occurs.
Given that the returned error code is not documented, is it correct to handle a specific return code of `0x800A0CC1' when i'm trying to trap the exception:
Item cannot be found in the collection
corresponding to the requested name or
ordinal
?
Since Microsoft didn't document the error code, they technically change it in the future.
They did document this error code, but it's hard to find:
ErrorValueEnum:
adErrItemNotFound 3265 -2146825023 0x800A0CC1 Item cannot be found in the collection that corresponds to the requested name or ordinal.
..so, as its' a documented error code, it is safe to test for it explicitly.
You'll have to decide whether or not it is worth the risk, but I believe that it is unlikely that Microsoft will change this error code. Checking for this particular error code is a pretty robust way to go.
Yes, it is fine. It is in fact a documented error code, although finding them is never easy. It is defined in the msdao15.idl Windows SDK file, adErrItemNotFound (error 3265)