NUnit3 Console runner saves test results in xml at the end of the test run. But in my case I want to save the partial results on each test failure, so that in case console runner crashes or is stopped, I can still get partial results for completed tests.
Is there a way to do that?
Test Results are saved regardless of failures or successful test runs. The XML file is generated for every test run. You could also write every test result to a log file if the XML is not generated for a particular test run.
Related
I want to exit test in the test case. And do not want the report to show the number of test cases (TC003) that exit test In the example below,
*** test cases ***
TC001
Run Keyword If '1'=='1' Log To Console xx
TC002
Run Keyword If '2'=='2' Log To Console xx
TC003
Run Keyword If '3'!='3' Exit Test
How do I use it? You can guide me
I don't think there's anything you can do. Once the test starts running, there's no way to remove it from the reports and logs.
It sounds like you're trying to skip a test under certain circumstances. If so, it will be able to mark a test as skipped (versus pass/fail) in robot framework 4.0, though it will still show up in the logs and reports.
If you really don't want it in the reports, you can write a script that removes the tests from the output.xml file and then regenerates the html logs and reports using rebot.
I'm trying to create a test case in Selenium IDE.
The idea is to split my whole test in smaller ones to help find problems in the execution.
Example of my test suite
I've created a test suite with all my small tests inside, and I'd like that the next test starts right where the last one stopped. But in the beginning of the execution, every test refreshes the browser.
Test Refreshing Browser on start of the execution
My question is:
Is it possible to run an entire test suite without refreshing the browser when a new test starts?
thanks a lot
I have a project where I am running 100 scenarios every day. After the run has complete, through listeners I am updating the pass/fail in an Excel sheet. I want to hear about a solution where, if I am running the test suite again, the passed test cases should be skipped and only failed test cases should run. I dont want to use retry.I tried to use skipException in beforeInvocation listener method but the test case is still executing the passed test case. How can I skip the passed test cases and execute only the failed one through listeners ?
Every time before the start of the scenario, it should go to the listener and check the excel sheet whether the scenario is passed or fail. If passed then the scenario should be skipped.
Any help will be greatly appreciated.
Update: I am able to do it through listeners, with skipException, but in my report it is showing test as failed and not as skipped
When you run bdd tests, qaf generates configuration file with name testng-failed-qas.xml under reports dir. You should use that config file to run only failed scenarios.
I run the test on bamboo with selenium technology and the test tab does not show the test failure, how I can view the test failure?
To see test results (including info which test caused fail) you need to add proper parser task to your job. There are many available parser tasks i.e. JUnit Parser, NUnit Parser, TestNG Parser.
The important thing is to move parser task under Final tasks bar (parser will execute even if previous task fail).
You don't have any test failures. In fact, no tests were running in this build as you can see in line
0 test in total
You job may have failed for one of 2 reasons:
Actual failure of the job. Check detailed log on Logs tab to see if this is the case
It may have also failed because you configured it to fail when there was no tests (and in this case there was no tests indeed) as we see. The corresponding configuration would look like this:
I have a small collection of integration tests that utilize selenium in a class. The idea is that these tests run every time there is a merge to the codebase, with the merge proceeding through the pipeline and having a series of tests running against the new code.
The thing is, these selenium tests have to run one at a time. They're using the browser to log into a website, and the account will just log out if more than one person tries to log into the account at once, it'll just log out, and the test will obviously fail, so I need these tests to run one at a time. I've tried using the #NotThreadSafe annotation, doesn't seem to have changed anything, and I've searched through for some sort of switch or parameter that defines how many tests run at once with no luck. These tests are using junit 4.12.