I have had Win 10 IoT Core running on a Raspberry Pi2, it was working fine, I had ported across my signage software, and all good, then the hdmi port stopped working ? my monitor just says no output, and goes into sleep mode. the Pi is running as I can assess it via the web portal, I can still deploy my application to it, and it says its running, but nothing been displayed.
I know that when using Linux there is a config file that you can modify, but what do you do with windows version ?
you have the configuration file for Windows too. check in the root of SD card. refer https://www.raspberrypi.org/forums/viewtopic.php?t=5851. You can try setting (this forces the board to use DVI mode instead of HDMI)
hdmi_group=2 # forces DVI timing to be used
It might also be due to low power input to the RP2, which could cause HTMI to not work. Try using USB3 or 1.5A~2.0A/ 5V adapter.
Ensure that you are running headed mode and not switched to headless by mistake. Details here: https://ms-iot.github.io/content/en-US/win10/HeadlessMode.htm
he display.
Related
What I want to do on my laptop:
Develop and Run on windows with Visual Studio (CUDA, TensorRT,...)
Develop and Run on Linux (CUDA, TensorRT,...)
Environment to edit videos, photoshop,...
Play games
Environment for general use (web browser, outlook, word,...)
Environment to test applications
Possibly connecting some external GPU to offload the work (cuda,...) from my laptop's graphics card. Since I'm new to this, I haven't researched enough to understand how it can be done. But, this is in my plans.
What I did and reaserched:
As a start, I created VM environements in my host Windows OS using VirtualBox for #1 and #2, but I cannot run inside VM, since it doesn't provide access to graphics card. Even if it did, I still need somehow to switch to a different environment when I want to play games for example.
I probably need hypervisor type 1 if I want to have environment to play games? But, in this case I'll need a second laptop to access it, right?
Is this even possible to do on one laptop (I have strong laptop with enough RAM and SSD)
Graphics cards (GPU) are PCI devices, so they can be passed to VMs with PCI Passthrough. A device is not accessible to the host during passthrough. Hot plug can be used to reattach a graphics card to a different VM or the host without rebooting.
I don't know if a Windows host supports GPU passthrough (maybe you need Windows Server), but Linux host and Windows guest seems to work.
Setting this up is easier if you have a second GPU that remains attached to the host or another computer to control the host during GPU passthrough, for example via SSH.
I used to work on my Virtual Box normally until it started giving me critical errors, so i backed up my machine and reinstalled virtualbox and loaded my backed up machine. Now i am working on a project that needs the use of the Webcam, so i use my PC's built in webcam usually. I used to enable it from the VM settings. However, now it the webcam seetings doesn't show in the devices. The photos below show the problem i am facing.
The image below shows that the webcam option is checked in the devices.
However, when i enter to enable my camera from the devices, i don't find the webcam options! (image below)
Is it recommended to reinstall my Virtual box again? If a solution couldn't be found?
The VirtualBox Extension Pack is required to allow Webcam passthrough.
Available here -
https://www.virtualbox.org/wiki/Downloads
I have what I believe to be a very simple question.
Context
I have a Raspberry Pi Zero W running Raspbian Lite (2020-02-13-raspbian-buster-lite.img).
Question
How do I change just one file on the SD Card, e.g. in the host partition, to auto-configure the raspberrypi as a wifi hostpot, and call it raspberrypi.
Also, I would like to be able to set the hotspot to be open, or with a password raspberry (just like the ssh password :) ).
What I tried already
I found lots of instructions on installing software packages, but unless I'm connecting via ssh already, then I can't run commands unless I'm already networked to the pi.
Why do I want this?
I want to be able to do this, for much greater ease of connecting to a raspberrypi in the first instance, for example, along with enabling ssh, this would allow very simple ease of access for incoming connections.
Only an idea
Finally, what does anyone think of the idea of enabling this by default in Raspbian. It can be disabled is required, but would substantially ease the process of connecting to a Pi with a Raspbian image out of the box - allowing a use to see so-called "proof-of-pi" immediately after first boot.
As far as I've seen, configuring the Pi before-first-boot by editing the boot partition files is limited. However there are some custom tools out there where you can look at creating a custom image or design some provisioning steps for your Pi.
PiBakery is a tool for creating custom images of Raspbian. Setting up a WiFi hotspot will most certainly require a custom script for tool installation and configuration.
I know that you can configure a SD card to auto-connect to WiFi (for normal network connections) by creating a wpa_supplicant.conf file and setting some values in boot's config.txt, you may want to check some of the documentation from the Raspbian project regarding config.txt. Keep in mind that the default raspberrypi.org image is slightly different than the Raspbian Project's image, so your mileage may vary.
Finally, depending on your use case for this/deployment strategy, you can also look into changing the Pi's boot mode so that it boots from a network host, kind of like "PXE Boot" for Windows machines. You'd have to host a provisioning server that the Pi can get information from and sync up with, which may be out of the bounds of what you're trying to accomplish, but I figured I'd bring it up!
When connecting HoloLens via USB to my computer, the device portal is still not available after setting it up as explained in the install tools page.
All I get in the browser 127.0.0.1:10080 is the generic "unable to connect" page.
Is there any way to know what is failing? What could I check? Any tip will be appreciated!
EDIT: browsers used: Edge, Firefox and Chrome.
EDIT2: Hololens development mode is on.
Connecting over USB requires the PC be running IPoverUSB, which is installed with the Windows 10 SDK. You can verify that it's running by checking the Services tab of Task Manager for IpOverUsbSvc.
FYI, another resolution to this issue may be the USB port you are using.
I initially was using a USB 3 port (which I've used to flash my HoloLens many times) and had the same issues.
On a whim, I switched to an older USB2 port and it's working perfectly now. SO try different USB ports if you are having this issue.
First of all, there's a similar thread on OpenQNX posted years ago but the solutions don't really apply for me.
Having said that, I want to create an OS image of QNX 6.6.0 to put on a Compact Flash card. This card is plugged in an USB adapter which is connected to my host pc. I'm running Neutrino in a VM (VMware/VirtualBox) for which I enabled USB support. Generally, the adapter works fine under Win (current host) and Linux.
The (apparently out-dated) tutorial I was following stated to search for devices named umass* or hd* after connecting the USB adapter. But there aren't any (except for hd0).
See also "ls /dev" screenshot.
The processes devb-umass and io-usb are running. So I expect that the adapter is detected automatically.
Any suggestions what went wrong?
OK, it seems that I had to restart the usb driver 'devb-umass' (several times). When the card reader is already plugged-in during the booting the driver will not detect it autoamtically. Thus one has to unplug and plug it in again after the devb-umass was getting re-started. It also might have been that the Host Controller Driver (HCD) was set to 'ohci' instead of 'ehci'.
Everything is working now as expected.
(Thanks Tim from the OpenQNX forum! ;) )