Related
If this question would be more appropriate on a related site, let me know, and I'd be happy to move it.
I have 165 vertices in ℤ11, all of which are at a distance of √8 from the origin and are extreme points on their corresponding convex hull. CGAL is able to calculate their d-dimensional triangulation in only 133 minutes on my laptop using just under a gigabyte of RAM.
Magma manages a similar 66 vertex case quite quickly, and, crucially for my application, it returns an actual polytope instead of a triangulation. Thus, I can view each d-dimensional face as a single object which can be bounded by an arbitrary number of vertices.
Additionally, although less essential to my application, I can also use Graph : TorPol -> GrphUnd to calculate all the topological information regarding how those faces are connected, and then AutomorphismGroup : Grph -> GrpPerm, ... to find the corresponding automorphism group of that cell structure.
Unfortunately, when applied to the original polytope, Magma's AutomorphismGroup : TorPol -> GrpMat only returns subgroups of GLd(ℤ), instead of the full automorphism group G, which is what I'm truly hoping to calculate. As a matrix group, G ∉ GL11(ℤ), but is instead ∈ GL11(𝔸), where 𝔸 represents the algebraic numbers. In general, I won't need the full algebraic closure of the rationals, ℚ̅, but just some field extension. However, I could make use of any non-trivially powerful representation of G.
With two days of calculation, Magma can manage the 165 vertex case, but is only able to provide information about the polytope's original 165 vertices, 10-facets, and volume. However, attempting to enumerate the d-faces, for any 2 ≤ d < 10, quickly consumes the 256 GB of RAM I have at my disposal.
CGAL's triangulation, on the other hand, only calculates collections of d-simplices, all of which have d + 1 vertices. It seems possible to derive the same facial information from such a triangulation, but I haven't thought of an easy way to code that up.
Am I missing something obvious in CGAL? Do you have any suggestions for alternative ways to calculate the polytope's face information, or to find the full automorphism group of my set of points?
You can use the package Combinatorial maps in CGAL, that is able to represent polytopes in nD. A combinatorial map describes all cells and all incidence and adjacency relations between the cells.
In this package, there is an undocumented method are_cc_isomorphic allowing to test if an isomorphism exist from two starting points. I think you can use this method from all possible pair of starting points to find all automorphisms.
Unfortunatly, there is no method to build a combinatorial map from a dD triangulation. Such method exists in 3D (cf. this file). It can be extended in dD.
I have implemented an algorithm that uses two other algorithms for calculating the shortest path in a graph: Dijkstra and Bellman-Ford. Based on the time complexity of the these algorithms, I can calculate the running time of my implementation, which is easy giving the code.
Now, I want to experimentally verify my calculation. Specifically, I want to plot the running time as a function of the size of the input (I am following the method described here). The problem is that I have two parameters - number of edges and number of vertices.
I have tried to fix one parameter and change the other, but this approach results in two plots - one for varying number of edges and the other for varying number of vertices.
This leads me to my question - how can I determine the order of growth based on two plots? In general, how can one experimentally determine the running time complexity of an algorithm that has more than one parameter?
It's very difficult in general.
The usual way you would experimentally gauge the running time in the single variable case is, insert a counter that increments when your data structure does a fundamental (putatively O(1)) operation, then take data for many different input sizes, and plot it on a log-log plot. That is, log T vs. log N. If the running time is of the form n^k you should see a straight line of slope k, or something approaching this. If the running time is like T(n) = n^{k log n} or something, then you should see a parabola. And if T is exponential in n you should still see exponential growth.
You can only hope to get information about the highest order term when you do this -- the low order terms get filtered out, in the sense of having less and less impact as n gets larger.
In the two variable case, you could try to do a similar approach -- essentially, take 3 dimensional data, do a log-log-log plot, and try to fit a plane to that.
However this will only really work if there's really only one leading term that dominates in most regimes.
Suppose my actual function is T(n, m) = n^4 + n^3 * m^3 + m^4.
When m = O(1), then T(n) = O(n^4).
When n = O(1), then T(n) = O(m^4).
When n = m, then T(n) = O(n^6).
In each of these regimes, "slices" along the plane of possible n,m values, a different one of the terms is the dominant term.
So there's no way to determine the function just from taking some points with fixed m, and some points with fixed n. If you did that, you wouldn't get the right answer for n = m -- you wouldn't be able to discover "middle" leading terms like that.
I would recommend that the best way to predict asymptotic growth when you have lots of variables / complicated data structures, is with a pencil and piece of paper, and do traditional algorithmic analysis. Or possibly, a hybrid approach. Try to break the question of efficiency into different parts -- if you can split the question up into a sum or product of a few different functions, maybe some of them you can determine in the abstract, and some you can estimate experimentally.
Luckily two input parameters is still easy to visualize in a 3D scatter plot (3rd dimension is the measured running time), and you can check if it looks like a plane (in log-log-log scale) or if it is curved. Naturally random variations in measurements plays a role here as well.
In Matlab I typically calculate a least-squares solution to two-variable function like this (just concatenates different powers and combinations of x and y horizontally, .* is an element-wise product):
x = log(parameter_x);
y = log(parameter_y);
% Find a least-squares fit
p = [x.^2, x.*y, y.^2, x, y, ones(length(x),1)] \ log(time)
Then this can be used to estimate running times for larger problem instances, ideally those would be confirmed experimentally to know that the fitted model works.
This approach works also for higher dimensions but gets tedious to generate, maybe there is a more general way to achieve that and this is just a work-around for my lack of knowledge.
I was going to write my own explanation but it wouldn't be any better than this.
Basically, I have a set of up to 100 co-ordinates, along with the desired tangents to the curve at the first and last point.
I have looked into various methods of curve-fitting, by which I mean an algorithm with takes the inputted data points and tangents, and outputs the equation of the cure, such as the gaussian method and interpolation, but I really struggled understanding them.
I am not asking for code (If you choose to give it, thats acceptable though :) ), I am simply looking for help into this algorithm. It will eventually be converted to Objective-C for an iPhone app, if that changes anything..
EDIT:
I know the order of all of the points. They are not too close together, so passing through all points is necessary - aka interpolation (unless anyone can suggest something else). And as far as I know, an algebraic curve is what I'm looking for. This is all being done on a 2D plane by the way
I'd recommend to consider cubic splines. There is some explanation and code to calculate them in plain C in Numerical Recipes book (chapter 3.3)
Most interpolation methods originally work with functions: given a set of x and y values, they compute a function which computes a y value for every x value, meeting the specified constraints. As a function can only ever compute a single y value for every x value, such an curve cannot loop back on itself.
To turn this into a real 2D setup, you want two functions which compute x resp. y values based on some parameter that is conventionally called t. So the first step is computing t values for your input data. You can usually get a good approximation by summing over euclidean distances: think about a polyline connecting all your points with straight segments. Then the parameter would be the distance along this line for every input pair.
So now you have two interpolation problem: one to compute x from t and the other y from t. You can formulate this as a spline interpolation, e.g. using cubic splines. That gives you a large system of linear equations which you can solve iteratively up to the desired precision.
The result of a spline interpolation will be a piecewise description of a suitable curve. If you wanted a single equation, then a lagrange interpolation would fit that bill, but the result might have odd twists and turns for many sets of input data.
so I am making a simple simulation of different planets with individual velocity flying around space and orbiting each other.
I plan to simulate their pull on each other by considering each planet as projecting their own "gravity vector field." Each time step I'm going to add the vectors outputted from each planets individual vector field equation (V = -xj + (-yj) or some notation like it) except the one being effected in the calculation, and use the effected planets position as input to the equations.
However this would inaccurate, and does not consider the gravitational pull as continuous and constant. Bow do I calculate the movement of my planets if each is continuously effecting the others?
Thanks!
In addition to what Blender writes about using Newton's equations, you need to consider how you will be integrating over your "acceleration field" (as you call it in the comment to his answer).
The easiest way is to use Euler's Method. The problem with that is it rapidly diverges, but it has the advantage of being easy to code and to be reasonably fast.
If you are looking for better accuracy, and are willing to sacrifice some performance, one of the Runge-Kutta methods (probably RK4) would ordinarily be a good choice. I'll caution you that if your "acceleration field" is dynamic (i.e. it changes over time ... perhaps as a result of planets moving in their orbits) RK4 will be a challenge.
Update (Based on Comment / Question Below):
If you want to calculate the force vector Fi(tn) at some time step tn applied to a specific object i, then you need to compute the force contributed by all of the other objects within your simulation using the equation Blender references. That is for each object, i, you figure out how all of the other objects pull (apply force) and those vectors when summed will be the aggregate force vector applied to i. Algorithmically this looks something like:
for each object i
Fi(tn) = 0
for each object j ≠ i
Fi(tn) = Fi(tn) + G * mi * mj / |pi(tn)-pj(tn)|2
Where pi(tn) and pj(tn) are the positions of objects i and j at time tn respectively and the | | is the standard Euclidean (l2) normal ... i.e. the Euclidean distance between the two objects. Also, G is the gravitational constant.
Euler's Method breaks the simulation into discrete time slices. It looks at the current state and in the case of your example, considers all of the forces applied in aggregate to all of the objects within your simulation and then applies those forces as a constant over the period of the time slice. When using
ai(tn) = Fi(tn)/mi
(ai(tn) = acceleration vector at time tn applied to object i, Fi(tn) is the force vector applied to object i at time tn, and mi is the mass of object i), the force vector (and therefore the acceleration vector) is held constant for the duration of the time slice. In your case, if you really have another method of computing the acceleration, you won't need to compute the force, and can instead directly compute the acceleration. In either event, with the acceleration being held as constant, the position at time tn+1, p(tn+1) and velocity at time tn+1, v(tn+1), of the object will be given by:
pi(tn+1) = 0.5*ai(tn)*(tn+1-tn)2 + vi(tn)*(tn+1-tn)+pi(tn)
vi(tn+1) = ai(tn+1)*(tn+1-tn) + vi(tn)
The RK4 method fits the driver of your system to a 2nd degree polynomial which better approximates its behavior. The details are at the wikipedia site I referenced above, and there are a number of other resources you should be able to locate on the web. The basic idea is that instead of picking a single force value for a particular timeslice, you compute four force vectors at specific times and then fit the force vector to the 2nd degree polynomial. That's fine if your field of force vectors doesn't change between time slices. If you're using gravity to derive the vector field, and the objects which are the gravitational sources move, then you need to compute their positions at each of the four sub-intervals in order compute the force vectors. It can be done, but your performance is going to be quite a bit poorer than using Euler's method. On the plus side, you get more accurate motion of the objects relative to each other. So, it's a challenge in the sense that it's computationally expensive, and it's a bit of a pain to figure out where all the objects are supposed to be for your four samples during the time slice of your iteration.
There is no such thing as "continuous" when dealing with computers, so you'll have to approximate continuity with very small intervals of time.
That being said, why are you using a vector field? What's wrong with Newton?
And the sum of the forces on an object is that above equation. Equate the two and solve for a
So you'll just have to loop over all the objects one by one and find the acceleration on it.
I've got a GPS track produced by gpxlogger(1) (supplied as a client for gpsd). GPS receiver updates its coordinates every 1 second, gpxlogger's logic is very simple, it writes down location (lat, lon, ele) and a timestamp (time) received from GPS every n seconds (n = 3 in my case).
After writing down a several hours worth of track, gpxlogger saves several megabyte long GPX file that includes several thousands of points. Afterwards, I try to plot this track on a map and use it with OpenLayers. It works, but several thousands of points make using the map a sloppy and slow experience.
I understand that having several thousands of points of suboptimal. There are myriads of points that can be deleted without losing almost anything: when there are several points making up roughly the straight line and we're moving with the same constant speed between them, we can just leave the first and the last point and throw away anything else.
I thought of using gpsbabel for such track simplification / optimization job, but, alas, it's simplification filter works only with routes, i.e. analyzing only geometrical shape of path, without timestamps (i.e. not checking that the speed was roughly constant).
Is there some ready-made utility / library / algorithm available to optimize tracks? Or may be I'm missing some clever option with gpsbabel?
Yes, as mentioned before, the Douglas-Peucker algorithm is a straightforward way to simplify 2D connected paths. But as you have pointed out, you will need to extend it to the 3D case to properly simplify a GPS track with an inherent time dimension associated with every point. I have done so for a web application of my own using a PHP implementation of Douglas-Peucker.
It's easy to extend the algorithm to the 3D case with a little understanding of how the algorithm works. Say you have input path consisting of 26 points labeled A to Z. The simplest version of this path has two points, A and Z, so we start there. Imagine a line segment between A and Z. Now scan through all remaining points B through Y to find the point furthest away from the line segment AZ. Say that point furthest away is J. Then, you scan the points between B and I to find the furthest point from line segment AJ and scan points K through Y to find the point furthest from segment JZ, and so on, until the remaining points all lie within some desired distance threshold.
This will require some simple vector operations. Logically, it's the same process in 3D as in 2D. If you find a Douglas-Peucker algorithm implemented in your language, it might have some 2D vector math implemented, and you'll need to extend those to use 3 dimensions.
You can find a 3D C++ implementation here: 3D Douglas-Peucker in C++
Your x and y coordinates will probably be in degrees of latitude/longitude, and the z (time) coordinate might be in seconds since the unix epoch. You can resolve this discrepancy by deciding on an appropriate spatial-temporal relationship; let's say you want to view one day of activity over a map area of 1 square mile. Imagining this relationship as a cube of 1 mile by 1 mile by 1 day, you must prescale the time variable. Conversion from degrees to surface distance is non-trivial, but for this case we simplify and say one degree is 60 miles; then one mile is .0167 degrees. One day is 86400 seconds; then to make the units equivalent, our prescale factor for your timestamp is .0167/86400, or about 1/5,000,000.
If, say, you want to view the GPS activity within the same 1 square mile map area over 2 days instead, time resolution becomes half as important, so scale it down twice further, to 1/10,000,000. Have fun.
Have a look at Ramer-Douglas-Peucker algorithm for smoothening complex polygons, also Douglas-Peucker line simplification algorithm can help you reduce your points.
OpenSource GeoKarambola java library (no Android dependencies but can be used in Android) that includes a GpxPathManipulator class that does both route & track simplification/reduction (3D/elevation aware).
If the points have timestamp information that will not be discarded.
https://sourceforge.net/projects/geokarambola/
This is the algorith in action, interactively
https://lh3.googleusercontent.com/-hvHFyZfcY58/Vsye7nVrmiI/AAAAAAAAHdg/2-NFVfofbd4ShZcvtyCDpi2vXoYkZVFlQ/w360-h640-no/movie360x640_05_82_05.gif
This algorithm is based on reducing the number of points by eliminating those that have the greatest XTD (cross track distance) error until a tolerated error is satisfied or the maximum number of points is reached (both parameters of the function), wichever comes first.
An alternative algorithm, for on-the-run stream like track simplification (I call it "streamplification") is:
you keep a small buffer of the points the GPS sensor gives you, each time a GPS point is added to the buffer (elevation included) you calculate the max XTD (cross track distance) of all the points in the buffer to the line segment that unites the first point with the (newly added) last point of the buffer. If the point with the greatest XTD violates your max tolerated XTD error (25m has given me great results) then you cut the buffer at that point, register it as a selected point to be appended to the streamplified track, trim the trailing part of the buffer up to that cut point, and keep going. At the end of the track the last point of the buffer is also added/flushed to the solution.
This algorithm is lightweight enough that it runs on an AndroidWear smartwatch and gives optimal output regardless of if you move slow or fast, or stand idle at the same place for a long time. The ONLY thing that maters is the SHAPE of your track. You can go for many minutes/kilometers and, as long as you are moving in a straight line (a corridor within +/- tolerated XTD error deviations) the streamplify algorithm will only output 2 points: those of the exit form last curve and entry on next curve.
I ran in to a similar issue. The rate at which the gps unit takes points is much larger that needed. Many of the points are not geographically far away from each other. The approach that I took is to calculate the distance between the points using the haversine formula. If the distance was not larger than my threshold (0.1 miles in my case) I threw away the point. This quickly gets the number of points down to a manageable size.
I don't know what language you are looking for. Here is a C# project that I was working on. At the bottom you will find the haversine code.
http://blog.bobcravens.com/2010/09/gps-using-the-netduino/
Hope this gets you going.
Bob
This is probably NP-hard. Suppose you have points A, B, C, D, E.
Let's try a simple deterministic algorithm. Suppose you calculate the distance from point B to line A-C and it's smaller than your threshold (1 meter). So you delete B. Then you try the same for C to line A-D, but it's bigger and D for C-E, which is also bigger.
But it turns out that the optimal solution is A, B, E, because point C and D are close to the line B-E, yet on opposite sides.
If you delete 1 point, you cannot be sure that it should be a point that you should keep, unless you try every single possible solution (which can be n^n in size, so on n=80 that's more than the minimum number of atoms in the known universe).
Next step: try a brute force or branch and bound algorithm. Doesn't scale, doesn't work for real-world size. You can safely skip this step :)
Next step: First do a determinstic algorithm and improve upon that with a metaheuristic algorithm (tabu search, simulated annealing, genetic algorithms). In java there are a couple of open source implementations, such as Drools Planner.
All in all, you 'll probably have a workable solution (although not optimal) with the first simple deterministic algorithm, because you only have 1 constraint.
A far cousin of this problem is probably the Traveling Salesman Problem variant in which the salesman cannot visit all cities but has to select a few.
You want to throw away uninteresting points. So you need a function that computes how interesting a point is, then you can compute how interesting all the points are and throw away the N least interesting points, where you choose N to slim the data set sufficiently. It sounds like your definition of interesting corresponds to high acceleration (deviation from straight-line motion), which is easy to compute.
Try this, it's free and opensource online Service:
https://opengeo.tech/maps/gpx-simplify-optimizer/
I guess you need to keep points where you change direction. If you split your track into the set of intervals of constant direction, you can leave only boundary points of these intervals.
And, as Raedwald pointed out, you'll want to leave points where your acceleration is not zero.
Not sure how well this will work, but how about taking your list of points, working out the distance between them and therefore the total distance of the route and then deciding on a resolution distance and then just linear interpolating the position based on each step of x meters. ie for each fix you have a "distance from start" measure and you just interpolate where n*x is for your entire route. (you could decide how many points you want and divide the total distance by this to get your resolution distance). On top of this you could add a windowing function taking maybe the current point +/- z points and applying a weighting like exp(-k* dist^2/accuracy^2) to get the weighted average of a set of points where dist is the distance from the raw interpolated point and accuracy is the supposed accuracy of the gps position.
One really simple method is to repeatedly remove the point that creates the largest angle (in the range of 0° to 180° where 180° means it's on a straight line between its neighbors) between its neighbors until you have few enough points. That will start off removing all points that are perfectly in line with their neighbors and will go from there.
You can do that in Ο(n log(n)) by making a list of each index and its angle, sorting that list in descending order of angle, keeping how many you need from the front of the list, sorting that shorter list in descending order of index, and removing the indexes from the list of points.
def simplify_points(points, how_many_points_to_remove)
angle_map = Array.new
(2..points.length - 1).each { |next_index|
removal_list.add([next_index - 1, angle_between(points[next_index - 2], points[next_index - 1], points[next_index])])
}
removal_list = removal_list.sort_by { |index, angle| angle }.reverse
removal_list = removal_list.first(how_many_points_to_remove)
removal_list = removal_list.sort_by { |index, angle| index }.reverse
removal_list.each { |index| points.delete_at(index) }
return points
end