I'm currently programming over an Atmega 168A micro controller through a USB Tiny programmer and an ISP interface.
The micro controller is set up with an external oscillator and an external person helped me by programming the corresponding fuses for its usage. The problem is I accidentally cleared the fuses and know avrdude can't communicate with the micro controller.
Every time I try to program I get the error:
avrdude: initialization failed, rc=-1
Double check connections and try again, or use -F to override
this check.
All connections are correct.
I'm working on a Mac where I installed Crosspack-AVR and an AVR plugin for Eclipse. How can I restore communication with the hardware?
Depends on that value you wrote to the fuses. If you disabled your external reset pin (RSTDISBL) or the serial programming interface (SPIEN) you only can use "high voltage" (high means 12V :-) programming. You may look for a capable programmer (eg. AVR dragon).
If you "just" screwed up the clock settings you can feed a clock signal to the XTAL1 pin and try to hook up your ISP programmer. You should increase the bit duration time to slow down the programming speed (i think it was the -B4 option)
If you set the lock bits you may trapped out yourself for ever.
If you program fuses always keep in mind, that a physical 0 means programmed and a 1 means unprogrammed. the tools are not consistent with this. some may show a checkmark if it is logically set (programmed = physically 0) some show the physical data.
If you use avr dude. i would recommend using AVR8 Burn-O-Mat that has a decent GUI for fuse settings of many AVR8 types.
Related
I'm trying to connect to stm32f401rbt6 with st-link utility.
The MCU has 6 pins connected, as on the image below.
The target is powered by a lab power supply, target GND is connected to the ST-Link GND
When I plug it to the computer, st-link utility says it can't connect.
Tried:
Update ST-Link firmware
Connect under reset is by default, tried all available methods
Checked connectivity for the pins on the image
Connected with the same ST-Link to other MCU
Desoldered the MCU and soldered another one
The issue is still remain. Please suggest what I'm doing wrong, or how to check that my MCU is alive.
I once had similiar issues and i figuered out, that decoupling capacitors were vital. After soldering this onto the pcb, it worked like a charm.
(Similar question: Stm32CubeProgrammer not connecting (no error msg) using ST-LINK V2 dongle and Lora E5 mini board)
You can try the following suggestions. Some ST devices are a lot more sensitive than others when it comes to programming. I have had some ST devices programming without issues and then using practically the same setup on other devices it just won't work.
Place a 22ohm resistor in series on the SWDIO and SWCLK lines. This link suggests only placing it on the SWDIO line but I found that I needed it on the SWCLK line as well. Typical SWD Circuit
For the ST Link Settings try using these:
Reduce the frequency from 4MHz to a lower frequency
Use SWD
Use connect under reset
Don't use an external pull-up on the NRST line.
Make sure that your programming wires between the ST-LINK and the target board are as short as is conveniently possible.
(This one I must stress as being important) Make sure that your processor's ground pins are all connected very closely together (i.e. the tracks between them are as short as possible) and that very importantly your programmer ground is also connected to the same ground pins very closely.- At high programming speeds a thin or long unbalanced (different length) ground track to the processor can cause a problem with some devices.
Whatever you are using to supply power to the processor must have a supply with a similar voltage as the ST-LINK (mine is 3V) - (although I have found that if the processor supply is 3.3V programming seems to still work most of the time.) (Remember the original ST-Link does not supply power only reads the power level.)
A dodgy programming setup can accidentally set the protection to LEVEL 2 bricking your device - so if you have been trying and not getting any further, it might be time to replace your IC.
Prior to changing / erasing a device that had been programmed to LEVEL 1, you might need to first enable the PCROP_RDP option byte. - Once enabled, you should be able to change from LEVEL 1 to LEVEL 0 that will automatically erase the device.
Some people have suggested holding the device in reset until just after pressing the erase button to enable erasing it.
I hope these suggestions help...
I want to read the global variables via the JTAG port, live, when a program is running on the microcontroller. Is it possible?
JTAG defines only a physical interface, it does not describe the on-chip debug capabilities of a particular processor which may or may not support access during execution.
Moreover whether it can be done in VB is not really the issue, the important issue is what hardware device and/or I/O port you are using for the JTAG interface, and whether a driver and API to access via .Net is available. That said VB.Net is not the first language I'd choose for that in any case.
A good place to start perhaps is OpenOCD, though it is not .Net specific.
"Almost-Live" is possibly doable, depending on the JTAG implementation. Often JTAG activity which reads memory does so by stealing cycles from the micro (or sometimes even inserting instructions into the pipeline). I'm not sure there's a micro which allows completely transparent access to memory over JTAG.
"All you need to do" is understand the JTAG implementation, know where the variable is located and issue a "memory read" command by wiggling the JTAG pins in the appropriate fashion. This is not a small task, which is why professional engineers are willing to pay (sometimes large amounts of) money for tools which perform this task.
Often the free (limited) toolchains the vendors provide can perform this also.
Yes, I suppose it is possible. But you'll need to drive the JTAG port (that sounds painful!) and know exactly where the data is stored on the chip, and what the formatting is.
I have a doubt regarding the reset due to power up:
As I know that microcontroller is hardwired to start with some particular memory location say 0000H on power up. At 0000h, whether interrupt service routine is written for reset(initialization of stack pointer and program counter etc) or the reset address is there at 0000h(say 7000) so that micro controller jumps at 7000 address and there initialization of stack and PC is written.
Who writes this reset service routine? Is it the manufacturer of microcontroller chip(Intel or microchip etc) or any programmer can change this reset service routine(For example, programmer changed the PC to 4000h from 7000h on power up reset resulting into the first instruction to be fetched from 4000 instead of 7000).
How the stack pointer and program counter are initialized to the respective initial addresses as on power up microcontroller is not in the state to put the address into stack pointer and program counter registers(there is no initialization done till reset service routine).
What should be the steps in the reset service routine considering all possibilities?
With reference to your numbering:
The hardware reset process is processor dependent and will be fully described in the data sheet or reference manual for the part, but your description is generally the case - different architectures may have subtle variations.
While some microcontrollers include a ROM based boot-loader that may contain start-up code, typically such bootloaders are only used to load code over a communications port, either to program flash memory directly or to load and execute a secondary bootloader to RAM that then programs flash memory. As far as C runtime start-up goes, this is either provided with the compiler/toolchain, or you write it yourself in assembler. Normally even when start-up code is provided by the compiler vendor, it is supplied as source to be assembled and linked with your application. The compiler vendor cannot always know things like memory map, SDRAM mapping and timing, or processor clock speed or what oscillator crystal is used in your hardware, so the start-up code will generally need customisation or extension through initialisation stubs that you must implement for your hardware.
On ARM Cortex-M devices in fact the initial PC and stack-pointer are in fact loaded by hardware, they are stored at the reset address and loaded on power-up. However in the general case you are right, the reset address either contains the start-up code or a vector to the start-up code, on pre-Cortex ARM architectures, the reset address actually contains a jump instruction rather than a true vector address. Either way, the start-up code for a C/C++ runtime must at least initialise the stack pointer, initialise static data, perform any necessary C library initialisation and jump to main(). In the case of C++ it must also execute the constructors of any global static objects before calling main().
The processor cores normally have as you say a starting address of some sort of table either a list of addresses or like ARM a place where instructions are executed. Wrapped around that core but within the chip can vary. Cores that are not specific to the chip vendor like 8051, mips, arm, xscale, etc are going to have a much wider range of different answers. Some microcontroller vendors for example will look at strap pins and if the strap is wired a certain way when reset is released then it executes from a special boot flash inside the chip, a bootloader that you can for example use to program the user boot flash with. If the strap is not tied that certain way then sometimes it boots your user code. One vendor I know of still has it boot their bootloader flash, if the vector table has a valid checksum then they jump to the reset vector in your vector table otherwise they sit in their bootloader mode waiting for you to talk to them.
When you get into the bigger processors, non-microcontrollers, where software lives outside the processor either on a boot flash (separate chip from the processor) or some ram that is managed somehow before reset, etc. Those usually follow the rule for the core, start at address 0xFFFFFFF0 or start at address 0x00000000, if there is garbage there, oh well fire off the undefined instruction vector, if that is garbage just hang there or sit in an infinite loop calling the undefined instruction vector. this works well for an ARM for example you can build a board with a boot flash that is erased from the factory (all 0xFFs) then you can use jtag to stop the arm and program the flash the first time and you dont have to unsolder or socket or pre-program anything. So long as your bootloader doesnt hang the arm you can have an unbrickable design. (actually you can often hold the arm in reset and still get at it with the jtag debugger and not worry about bad code messing with jtag pins or hanging the arm core).
The short answer: How many different processor chip vendors have there been? There are many different solutions, as many as you can think of and more have been deployed. Placing a reset handler address in a known place in memory is the most common though.
EDIT:
Questions 2 and 3. if you are buying a chip, some of the microcontrollers have this protected bootloader, but even with that normally you write the boot code that will be used by the product. And part of that boot code is to initialize the stack pointers and prepare memory and bring up parts of the chip and all those good things. Sometimes chip vendors will provide examples. if you are buying a board level product, then often you will find a board support package (BSP) which has working example code to bring up the board and perhaps do a few things. Say the beagleboard for example or the open-rd or embeddedarm.com come with a bootloader (u-boot or other) and some already have linux pre-installed. boards like that the user usually just writes some linux apps/drivers and adds them to the bsp, but you are not limited to that, you are often welcome to completely re-write and replace the bootloader. And whoever writes the bootloader has to setup the stacks and bring up the hardware, etc.
systems like the gameboy advance or nds or the like, the vendor has some startup code that calls your startup code. so they may have the stack and such setup for them but they are handing off to you, so much of the system may be up, you just get to decide how to slice up the memorires, where you want your stack, data, program, etc.
some vendors want to keep this stuff controlled or a secret, others do not. in some cases you may end up with a board or chip with no example code, just some data sheets and reference manuals.
if you want to get into this business though you need to be prepared to write this startup code (in assembler) that may call some C code to bring up the rest of the system, then that might start up the main operating system or application or whatever. Microcotrollers sounds like what you are playing with, the answers to your questions are in the chip vendors users guides, some vendors are better than others. search for the word reset or boot in the document to try to figure out what their boot schemes are. I recommend you use "dollar votes" to choose the better vendors. A vendor with bad docs, secret docs, bad support, dont give them your money, spend your money on vendors with freely downloadable, well written docs, with well written examples and or user forums with full time employees trolling around answering questions. There are times where the docs are not available except to serious, paying customers, it depends on the market. most general purpose embedded systems though are openly documented. the quality varies widely, but the docs, etc are there.
Depends completely on the controller/embedded system you use. The ones I've used in game development have the IP point at a starting address in RAM. The boot strap code supplied from the compiler initializes static/const memory, sets the stack pointer, and then jumps execution to a main() routine of some sort. Older systems also started at a fixed address, but you manually had to set the stack, starting vector table, and other stuff in assembler. A common name for the starting assembler file is CRT0.s for the stuff I've done.
So 1. You are correct. The microprocessor has to start at some fixed address.
2. The ISR can be supplied by the manufacturer or compiler creator, or you can write one yourself, depending on the complexity of the system in question.
3. The stack and initial programmer counter are usually handled via some sort of bootstrap routine that quite often can be overriden with your own code. See above.
Last: The steps will depend on the chip. If there is a power interruption of any sort, RAM may be scrambled and all ISR vector tables and startup code should be rewritten, and the app should be run as if it just powered up. But, read your documentation! I'm sure there is platform specific stuff there that will answer these for your specific case.
I had a look at this and this but no one sounded particularly sure of their ideas and I'm kind of after a different thing anyway. I want to hook my usb power cables (red and black) up to my phone so I don't have to use a battery (the battery is dead anyway and this is just an experiment). The problem is that USB standards ensure that a minimum of 4.35V is supplied, when I only want 3.7V. Does anyone know for sure that you can or cannot regulate power output programmatically? Some other queries I have are: What kind of power does the sleep mode provide? And what would I need to code something in to play with this, C++?
No, you won't find a computer that allows you to set this voltage in software. It would break the USB specification.
You can get 150mA by default, and 500mA if your USB device negotiates it with the computer (requiring a little bit of logic in the device). Multiply by 5V to get the provided power.
A bit more info on the answer from Pascal:
The normal operation (Non-Configured mode) is 100mA
In theory, the operating system should check the MaxPower value of the device's configuration descriptor to decide if to allow it to draw more than 100mA.
In practice, PCs do not do it (and have no way to control it). So you can try taking 500mA.
(Of course connecting a bus powered hub and linking more then one 500mA device, should, not work.)
If the device is not actively used, the OS may (and should) suspend it. When suspended the power is limited to 1-0.5mA (Again, in theory, since it can not be controlled by software).
I have been tasked to write a device driver for an embedded device which will communicate with the micro controller via the SPI interface. Eventually, the USB interface will be used to download updated code externally and used during the verification phase.
My question is, does anyone know of a good reference design or documentation or online tutorial which covers the implementation/design of the USB protocol stack/device driver within an embedded system? I am just starting out and reading through the 650 page USB v2.0 spec is a little daunting at the moment.
Just as a FYI, the micro controller that I am using is a Freescale 9S12.
Mark
Based upon goldenmean's (-AD) comments I wanted to add the following info:
1) The embedded device uses a custom executive and makes no use of a COTS or RTOS.
2) The device will use interrupts to indicate data is ready to be retrieved from the device.
3) I have read through some of the docs regarding Linux, but since I am not at all familiar with Linux it isn't very helpful at the moment (though I am hoping it will be very quickly).
4) The design approach, for now at least, it to write a device driver for the USB device then a USB protocol layer (I/O) would reside on top of the device driver to interpret the data. I would assume this would be the best approach, though I could be wrong.
Edit - A year later
I just wanted to share a few items before they vanish from my mind in case I never work on a USB device again. I ran into a few obstacles when developing code and getting it up and running for the first.
The first problem I ran into was that when the USB device was connected to the Host (Windows in my case) was the host issues a Reset request. The USB device would reset and clear the interrupt enable flags. I didn't read the literature enough to know this was happening, thus I was never receiving the Set-Up Request Interrupt. It took me quite a while to figure this out.
The second problem I ran into was not handling the Set-Up Request for Set_Configuration properly. I was handling it, but I was not processing the request correctly in that the USB device was not sending an ACK when this Set-Up Request came in. I eventually found this out by using a hardware USB protocol analyzer.
There were other issues that I ran into, but these were the two biggest ones that took me quite a while to figure out. The other issue I had to worry about is big-endian and little-endian, Freescale 9S12 vs USB data format (Intel), respectively.
I ended up building the USB device driver similar to UART device drivers I had done in the past. I have posted the code to this at the following URL.
http://lordhog.wordpress.com/2010/12/13/usb-drive
I tend to use structures a lot, so people may not like them since they are not as portal as using #defines (e.g., MAX3420_SETUP_DATA_AVAIL_INT_REQR 0x20), but I like them since it makes the code more readable for me. If anyone has questions regarding it please feel free to e-mail and I can try to give some insight to it. The book "USB Complete: The Developer's Guide" was helpful, so long as you knew what areas to concentrate on. This was a simple application and only used low-speed USB.
While writing a device driver for any interface (USB, Parallel port, etc...) the code needed to be developed would depend upon whether there is any Operating System(OS), RTOS running on that Processor/Micro controller.
e.g. if thats going to run say WinCE - It will have its own Driver development Kit , and steps to be followed in the device driver development. Same for any other OS like Linux, symbian.
If its going to be a plain firmware code(No OS) which is going to control the processor/microcontroller, then it's a different situation altogether.
So based on either of the above situation u are in, one needs to read & understand:-
1.) The Hardware Specification of the processor/micro controller development board - Register files, ports, memory layout, etc.
2.) USB spec
3.) Couple of pointers i found quickly. Google shud be ur friend!
http://www.lrr.in.tum.de/Par/arch/usb/usbdoc/ - Linux USB device driver
http://www.microsoft.com/technet/archive/wce/support/usbce.mspx
-AD
I've used an earlier edition of USB Complete by Jan Axelson. Indeed very complete.
From the editorial review:
Now in its fourth edition, this developer's guide to the Universal Serial Bus (USB) interface covers all aspects of project development, such as hardware design, device firmware, and host application software.
I'm curious, why did you pick the 9S12? I used it at a previous job, and was not pleased.
It had lousy gcc support so we used Metrowerks
which may have been okay for C, but often generated buggy C++
had a lousy IDE with binary project files!
The 9s12 was also slow, a lot of instructions executed in 5 cycles.
Not very power efficient, either.
no barrel shifter, made operations that are common in embedded code slow
not that cheap.
About the only thing I dislike more is an 8051. I'm using an ARM CortexM3 at my current job, it's better than a 9S12 in every way (faster clock, more work done per clock, less power consumption, cheaper, good gcc support, 32-bit vs. 16-bit).
I don't know which hardware you're planning to use but assuming that's flexible, STMicro offers a line of microcontrollers with USB/SPI support and a library of C-code that can be used with their parts. -- I've used their ARM7 series micros for years with great success.
Here is an excellent site maintained by Jonathan Valvano, a professor at the University of Texas. He teaches four courses over there (three undergraduate, one graduate), all are about using a 9S12 microcontroller. His site contains all the lecture notes, lab manuals, and more importantly, starter files, that he uses for all his classes.
The website looks like it's from the 90's, but just dig around a bit and you should find everything you need.
users.ece.utexas.edu/~valvano/
Consider AVR for your next MCU project because of it's wonderful LUFA and V-USB libraries.
I'm working on a project using the Atmel V71. The processor is very powerful and among lot's of high end connectivity offered on chip is a USB engine that will do device or host modes for 480 Mhz or 48Mhz (not USB 3.0). The tools are free and come with a number of host and device USB example projects with all the USB stack code right there. It supports 10 end points and all the transfers are done via DMA so you have most of the processor horsepower available for other tasks. The Atmel USB stack works without needing an RTOS