I want to interface two microcontrollers with a UART interface and I search a protocol to exchange data between them.
In practice, I want to exchange data periodically (ie: sensors reading) and also data on event (GPIO state). I have around 100-200 bytes to exchange every 100 milli second.
Does anybody know a protocol or library to achieve this kind of task ?
For now, I see protobuf and nano protobuff ? Is there something else ?
It would be nice if I could add a software layer over the UART and use "virtual data stream" like if it was a TCP/IP connection to N ports.
Any idea ?
Thanks
I think the most straight forward way is to roll your own.
You'll find RS232 drivers in the manufacturers chip support library.
RS232 is a stream oriented transport, that means you will need to encode your messages into some frameing structure when you send them and detect frame boundaries on the receiver side. A clever and easy to use mechanism to do this is "Consistent Overhead Byte Stuffing".
https://en.wikipedia.org/wiki/Consistent_Overhead_Byte_Stuffing
This simple algorithm turns zeros in your messages into some other value, so the zero-byte can be used to detect start and end of frame. If a byte gets corrupted on the way you can even resynchronize to the stream and keep going.
The code on Wikipedia should be easy enough even for the smallest micro-processors.
Afterwards you can define your message format. You can probably keep it very simple and directly send your data-structures as is.
Suggestion for a simple message format:
Byte-ID Meaning
---------------------------------
0 Destination port number
1 message type (define your own)
2 to n message data
If you want to send variable length messages you can either send out a length byte or derive the length from the output of the Constant Overhead Byte Stuffing framing.
By the way, UART/RS232 is nice and easy to work with, but you may also want to take a look at SPI. The SPI interface is more suitable to exchange data between two micro-controllers. It is usually faster than RS232 and more robust because it has a dedicated clock-line.
How about this: eRPC https://community.nxp.com/docs/DOC-334083
The eRPC (Embedded Remote Procedure Call) is a Remote Procedure Call (RPC) system created by NXP. An RPC is a mechanism used to invoke a software routine on a remote system using a simple local function call. The remote system may be any CPU connected by an arbitrary communications channel: a server across a network, another CPU core in a multicore system, and so on. To the client, it is just like calling a function in a library built into the application. The only difference is any latency or unreliability introduced by the communications channel.
I have use it in a two processor embedded system, a cortext-A9 CPU with a Context-M4 MCU, which communicate each other with SPI/GPIO.
Erpc can run over UART, SPI, rpmsg and network(tcp). even when using serial or SPI as transport tunnel, it can do bidirectional
calls and with very minimal footprint.
Simple serial point-to-point communication protocol
http://www.zipplet.co.uk/index.php/content/openformats_mise
It depends if you need master/slave implementation, noise protection, point-point or multi-point (and in this case collision detection), etc
but, as our colleague said, I would go with the simplest solution that fits the problem, following the KISS principle http://en.wikipedia.org/wiki/KISS_principle
Just add some header information like ID and length, if necessary CRC checking, and be happy :)
Try Microcontroller Interconnect Network (MIN) 1.0:
https://github.com/min-protocol/min
It has framing using byte-stuffing to keep receiver sync, 16-bit Fletcher's algorithm for checksum, an identifier for use by the application and a variable payload of up to 15 bytes.
There's embedded C code there plus also a Python implementation to make it easier to talk to a PC.
As the first answer starts, the simplest result is to roll your own. Define your header (the "format" above) as needed, perhaps including status information so each processor knows that the other is working properly. I have had success with a protocol that includes
2 byte ascii prefix and suffix such as "[" and "]" so that a
protocol analyzer can show you message boundaries.
The number of bytes.
The command ID (parsed to indicate what command handler to use.
Command arguments (I used 3 32 bit words).
A CRC or checksum to verify transfer integrity
The parser then recognizes the [* as the start of the message, and dispatches the body to the command handler for the particular command ID with the associated arguments as long as the checksum matches.
Related
I'm trying to design an efficient communication protocol between a micro-controller on one side and an ARM processor on a multi-core TI chip on the other side through SPI.
The requirements for the needed protocol:
1 - Multi-session with queuing support, as I have multiple sending/receiving threads, so it will be more than one application using this communication protocol and I need the protocol to handle queuing these requests (I will keep holding the buffer if the transmission is queue but I just need the protocol to manage scheduling the queues).
2 - Works over SPI as an underlying protocol.
3 - Simple error checking.
In this thread: "Simple serial point-to-point communication protocol", PPP was a recommended option, however I see PPP does only part of the job.
I also found Light weight IP (LwIP) project featuring PPP over serial (which I assume that I can use it over SPI), so I thought about the possibility of utilizing any of the upper layers protocols like TCP/UDP to do the rest of the required jobs. Fortunately, I found TI including LwIP as part of their ethernet SW in the starterware package, which I assume to ease porting at least on the TI chip side.
So, my questions are:
1 - Is it valid to use LwIP for this communication scheme? Won't this introduce much overhead due to IP headers which are not necessary for a point to point (on the chip level) communication and kill the throughput?
2 - Will the TCP or any similar protocol residing in LwIP handle the queuing of transmission requests, for example if I request transmission through a socket while the communication channel is busy transmitting/receiving request for another socket (session) of another thread, will this be managed by the protocol stack? If so, which protocol layer manages it?
3 - Is their a more efficient protocol stack than LwIP, that meets the above requirements?
Update 1: More points to consider
1 - SPI is the only available option, I use it with available GPIOs to indicate to the master when the slave has data to send.
2 - The current implemented (non-standard) protocol uses DMA with SPI, and a message format of《STX_MsgID_length_payload_ETX》with a fixed message fragments length, however the main drawback of the current scheme is that the master waits for a response on the message (not fragment) before sending another one, which kills the throughput and does not utilise the full duplex nature of SPI.
3- An improvement to this point was to use a kind of mailbox for receiving fragments, so a long message can be interrupted by a higher priority one so that fragments of a single message can arrive non sequentially, but the problem is that this design lead to complicating things especially that I don't have much available resources for many buffers to use the mailbox approach on the controller (master) side. So I thought that it's like I'm re-inventing the wheel by designing a protocol stack for a simple point to point link which may not be efficient.
4- What kind of higher level protocols can be normally used above SPI to establish multiple sessions and solve the queuing/scheduling of messages?
Update 2: Another useful thread "A good serial communications protocol/stack for embedded devices?"
Update 3: I had a look at Modbus protocol, it seems to specify the application layer then directly the data link layer for serial line communication, which sounds to skip the unnecessary overhead of network oriented protocols layers.
Do you think this will be a better option than LwIP for the intended purpose? Also, is there a widely used open source implementation like LwIP but for Modbus?
I think that perhaps you are expecting too much of the humble SPI.
An SPI link is little more a pair of shift registers one in each node. The master selects a single node to connect to its SPI shift register. As it shifts in its data, the slave simultaneously shifts data out. Data is not exchanged unless the master explicitly clocks the data out. Efficient protocols on SPI involve the slave having something useful to output while the master inputs. This may be difficult to arrange, so you usually need a means of indicating null data.
PPP is useful when establishing a connection between two arbitrary endpoints, when the endpoints are fixed and known a priori, PPP would serve no purpose other than to complicate things unnecessarily.
SPI is not a very sophisticated nor flexible interface and probably unsuited to heavyweight general purpose protocols such as TCP/IP. Since "addressing" on SPI is performed by physical chip-select, the addressing inherent in such protocols is meaningless.
Flow control is also a problem with SPI. The master has no way of determining that the slave has copied the data from SPI the shift register before pushing more data. If your slave SPI supports DMA you would be wise to use it.
Either way I suggest that you develop something specific to your purpose. Since SPI is not a network as such, you only need a means to address threads on the selected node. This could be as simple as STX<thread ID><length><payload>ETX.
Added 27 September 2013 in response to comments
Generally SPI as its names suggests is used to connect to peripheral devices, and in that context the protocol is defined by the peripheral. EEPROMS for example typically use a common or at least compatible command interface across vendors, and SD/MMC card SPI interface uses a standardised command test and protocol.
Between two microcontrollers, I would imagine that most implementations are proprietary and application specific. Open protocols are designed for generic interoperability and to achieve that might impose significant unnecessary overhead for a closed system, unless perhaps the nodes were running a system that already had a network stack built in.
I would suggest that if you do want to use a generic network stack that you should abstract the SPI with device drivers at each end that give the SPI a standard I/O stream interface (open(), close(), read(), write() etc.), then you can use the higher-level PPP and TCP/IP protocols (although PPP can probably be avoided since the connection is permanent). However that would only be attractive if both nodes already supported these protocols (running Linux for example), otherwise it will be significant effort and code for little benefit, and would certainly not be "efficient".
I assume you dont really want or have room for a full ip (lwip) stack on the microcontroller? This just sounds like a lot of overkill. Why not just roll your own simple packet structure to move the data items you need to move. Depending on how spi is supported on both sides you may or may not be able to use it to define the frame for your data, if not a simple start pattern, length and a trailing checksum and maybe tail pattern would suffice for finding packet boundaries in the stream (no different than a serial/uart solution). You can even use the PPP solution for that with a start pattern and I think end pattern with the payload using a two byte pattern whenever the start pattern happens to show up in the data. I dont remember all the details now.
Whatever your frame is then add a packet type and your handshakes, or if the data is going to just be microcontroller to arm then you dont even need to do that.
To get back to your direct question. Yes, I think that an ip stack (lwip or other) will introduce a lot of overhead. both bandwidth and more important the amount of code needed to support that stack will chew up rom/ram on both sides. If you ultimately need to present this data in an ip fashion (a website hosted by the embedded system) then somewhere in the path you need an ip stack, etc.
I cant imagine that lwip manages your queues for you. I assume you would need to do that yourself. the various queues might want to talk to a single driver that deals with the single spi bus (assuming there is a single spi bus with multiple chip selects). It also depends on how you are using the spi interface, if you are allowing the arm to talk to multiple microcontrollers and the packets of data are broken up into a little bit from this controller a little from that controller so that nobody has to wait to long before they get a few more bytes of data. Or will a complete frame have to move from one microcontroller before moving onto the next gpio interrupt to pull that guys data? The long and short of it is I would assume you have to manage the shared resource just like you would in any other situation where you have multiple users of a shared resource (rtos, full blown operating system, etc). I dont remember lwip that well at all but with a full blown berkeley sockets application interface the user could write separate applications where each application only cared about one TCP or UDP port and the libraries and drivers managed separating those packets out to each application as well as all of the rules for the IP stack.
If you are not already doing experiments with moving data over the spi interface(s) I would start with simple experiments first just to get the feel for how well it is or isnt going to work, the sizes of transfers you can do reliably per spi transction, etc. Your solution may naturally just fall out of those experiments.
I'm doing a USB device is to control stepper motors. I've done this before using a parallel port. because these ports do not exist in current motherboards, I decided to implement a USB communication between my device and the PC (host).
To achieve My objective, I endowed the freescale microcontroller the device with that has a USB module 12Mbps.
My USB device must receive 4 bytes (one for each motor driver) at a given time, because every byte is a step that should move the engine.
In the PC (Host) an application of user processes a text file with information and make the trajectory coordinates sending bytes at a certain rate for each motor (time is trivial to achieve the acceleration and speed of the motors) .
Using the parallel port was an easy the task because each byte is sent sequentially to a time determined by the user app.
doing a little research about full speed USB protocol understood that the frame is sent every 1ms.
then you can send 4 byte or many more every 1ms but I can not manage time like I did with the parallel port.
My microcontroller can send up to 64 bytes per frame (Based on transfer papers type Control, Bulk, Int, Iso ..).
question 1:
I want to know in what way I can send 4-byte packets faster than every 1 ms?
question 2:
What type of transfer can advise me for these type of devices?
Thanks.
Like Ricardo said, USB-serial will suffice.
As for the type of transfer, try implementing a CDC stack and use your SCI receiver to listen for PC commands. That will give you a receive buffer which will meet your needs.
Initialize your SCI (baud, etc)
Enable receiver and interrupt
On data receive, move it to your 4-byte command buffer
Clear receive buffer, wait for more
When you have all 4 bytes, fire off the steppers! Four bytes should take µs.
Check with Freescale to see if your processor is supported.
http://cache.freescale.com/files/microcontrollers/doc/support_info/USB_STACK_RELEASE_NOTES_V4.1.1.pdf?fpsp=1
There might even be some sample code to get you started.
-Cheers
I am achieving the same goal (driving/control CNC machines) like this:
the USB device is just synchronous I/O parallel port. Using continuous bulk transfer one pipe as input and one as output. This way I was able to achieve synchronous 64bit parallel communication with ~70KHz sample rate. It uses traffic around (i)4.27+(o)4.27 MBit/s that is limit for mine MCU and code. Bigger speeds cause jitter on the output due to USB events interrupts.
How to do it (on MCU side)
I have 2 FIFO's one for ingoing and one for outgoing data. I have timer interrupt occurring with sample rate frequency. In it I read the inputs and feed it to the first FIFO and read data from the other FIFO and send it to the outputs.
On top of that the USB task is called (inside the same interrupt) checking FIFO for sending to and incoming data from USB handling the transfer itself
I choose ATMEL AT32UC3A chips for this task. After a long and pain full research I decided these MCU's because they have enough memory for both FIFO's and program so no need for additional IC. It has FPGA package which can be used (BGA is not an option). It has HS USB (most USB MCU's have only FS like yours). It runs at 66MHz. It supports many interesting features (did interesting projects with it in the past) and of coarse I have experience with ATMEL MCU's from past
So if you want to achieve something similar then
start with bulk transfer (PC -> USB -> MCU -> output)
add FIFO if needed
do not know the sample rate you need. The old LPT's could handle from 80-196KHz depend on the manufactor. The modern ones are much much slower (which is silly and sad).
measure the critical sample rate
you need oscilloscope or very good hearing for this. The output data must be synchronous so no holes in it, no jitter, etc...
if any of these are present you have to lower the sample rate. Mine setup could handle even 1MHz sample rate but the USB jitter was present (sometimes USB event froze the sending for longer that one sample...) so I achieve only 70KHz of stable output.
if needed also inputs then add them
but only if the output is working as it should. Do not forget to lower the sample rate after this too ... Use separate bulk pipes and FIFOs for input and output.
I's using Qt to build Udp and Tcp servers/clients. Now in recent project, Qt is not allowed and i'm supposed to use Boost. Having gone through boost::asio, i feel confused since there are so many features and usages are very different from Qt. For Udp (multicast,broadcast etc) i'm more or less clear now. But for Tcp i'm having problems understanding:
(have to do all async)
TCP is stream oriented so there is no way to know the number of bytes that have arrived. So we use asio::ip::tcp::socket::async_read_some(). However in Qt we have readAll() for a socket which can be made to read all data on readyRead() signal and return a QByteArray, the size of which we needn't specify as it can grow. How do i achieve this in Boost? readyRead() signal i think would map roughly to async_read_some(), what about the rest (readAll() and "growable" buffer/array?
disconnected() signal is emitted in Qt if the TCP connection disconnects (server/client off, lan cable unplugged etc). What would be the equivalent check in Boost? Do i need a timer to periodically send and expect heartbeat messages myself?
Use some overload of async_read free function with the appropriate completion-condition.
As you see there, this function accepts asio::streambuf, which is growing automatically.
Yes, the only portable & reliable way is to send some heartbeat. I don't know how Qt does that, but try cutting the network cable and see whether you get any notification from Qt...
I'm working on a communication protocol between embedded devices. The protocol will definitely need new commands and fields in the future. What do I need to do to make sure I'm not painting myself into a corner?
This is a wide open question. Here are some random thoughts about it:
Leave spares.
Use a very basic header with a "number of bytes to follow" field.
If there are enumerated message types, make sure the type field can accomodate
growth.
If you use bitflags, leave spares.
Possibly include a "raw data" message, which can be used to wrap any protocol future generations think up.
In summary, Leave spares.
If at all possible, allow a human at one end of a cable to figure out what is at the other end of the cable.
Ideally, a human could hook up a dumb terminal and hit the keyboard three times (Enter Question-mark Enter), then a long, detailed message would come back describing what kind of machine it is, what is its model number, the name and phone number and web site of the organization that built it, the "official" protocol version number, and the unofficial build time:
__DATE__ ": " __TIME__
Also send the same detailed message every time the machine boots up.
If at all possible, try to design your protocol so that a human being with a dumb terminal can talk to your device.
The HTTP is one such human-readable protocol, and I suspect this is one of the reasons for its popularity.
Human-readable implies, among other things:
Limit yourself to characters that a human can read and type.
Avoid special control characters. Take advantage of the power of plain text.
Always send CR+LF at the end of each packet (as mandated by many Internet protocols).
Accept characters at any rate, from maximum-speed file upload from a PC to a non-touch-typing human slowly pecking at a keyboard.
You might also want to glance over the list of common protocols for embedded systems.
Perhaps one already meets your requirements?
Is there any reason to use something more difficult to decode than the standard Netstring format?
The question is a little too general for a clear answer. There are many aspects an embedded system may need to communicate like;
How many peers will it need to communicate with?
How much data does it need to communicate?
How tightly synchronized do the systems need to be?
What is the physical media for the protocol and what are the bandwidth limitations, and error susceptibility considerations?
All of these requirements and resource limitations will certainly constrain the system and then you can start to figure out what the protocol will need. Once you know these issues you can then project how some the requirements may change/expand in the future. From there you can design the protocol to accommodate(or not) the worst case use cases.
I would use HDLC. I have had good luck with it in the past. I would for a point to point serial just use the Asynchronous framing and forget about all of the other control stuff as it would probably be overkill.
In addition to using HDLC for the framing of the packet. I format my packet like the following. This is how options are passed using 802.11
U8 cmd;
U8 len;
u8 payload[len];
The total size of each command packet is len +2
You then define commands like
#define TRIGGER_SENSOR 0x01
#define SENSOR_RESPONSE 0x02
The other advantage is that you can add new commands and if you design your parser correctly to ignore undefined commands then you will have some backwards compatibility.
So putting it all together the packet would look like the following.
// total packet length minus flags len+4
U8 sflag; //0x7e start of packet end of packet flag from HDLC
U8 cmd; //tells the other side what to do.
U8 len; // payload length
U8 payload[len]; // could be zero len
U16 crc;
U8 eflag; //end of frame flag
The system will then monitor the serial stream for the flag 0x7e and when it is there you check the length to see if it is pklen >= 4 and pklen=len+4 and that the crc is valid. Note do not rely on just crc for small packets you will get a lot of false positives also check length. If the length or crc does not match just reset the length and crc and start with decoding the new frame. If it is a match then copy the packet to a new buffer and pass it to your command processing function. Always reset length and crc when a flag is received.
For your command processing function grab the cmd and len and then use a switch to handle each type of command. I also require that a certain events send a response so the system behaves like a remote procedure call that is event driven.
So for example the sensor device can have a timer or respond to a command to take a reading. It then would format a packet and send it to the PC and the PC would respond that it received the packet. If not then the sensor device could resend on a timeout.
Also when you are doing a network transfer you should design it as a network stack like the OSI modle. The HDLC is the data link layer and the RPC and command handling is the Application Layer.
I am building a small device with its own CPU (AVR Mega8) that is supposed to connect to a PC. Assuming that the physical connection and passing of bytes has been accomplished, what would be the best protocol to use on top of those bytes? The computer needs to be able to set certain voltages on the device, and read back certain other voltages.
At the moment, I am thinking a completely host-driven synchronous protocol: computer send requests, the embedded CPU answers. Any other ideas?
Modbus might be what you are looking for. It was designed for exactly the type of problem you have. There is lots of code/tools out there and adherence to a standard could mean easy reuse later. It also support human readable ASCII so it is still easy to understand/test.
See FreeModBus for windows and embedded source.
There's a lot to be said for client-server architecture and synchronous protocols. Simplicity and robustness, to start. If speed isn't an issue, you might consider a compact, human-readable protocol to help with debugging. I'm thinking along the lines of modem AT commands: a "wakeup" sequence followed by a set/get command, followed by a terminator.
Host --> [V02?] // Request voltage #2
AVR --> [V02=2.34] // Reply with voltage #2
Host --> [V06=3.12] // Set voltage #6
AVR --> [V06=3.15] // Reply with voltage #6
Each side might time out if it doesn't see the closing bracket, and they'd re-synchronize on the next open bracket, which cannot appear within the message itself.
Depending on speed and reliability requirements, you might encode the commands into one or two bytes and add a checksum.
It's always a good idea to reply with the actual voltage, rather than simply echoing the command, as it saves a subsequent read operation.
Also helpful to define error messages, in case you need to debug.
My vote is for the human readable.
But if you go binary, try to put a header byte at the beginning to mark the beginning of a packet. I've always had bad luck with serial protocols getting out of sync. The header byte allows the embedded system to re-sync with the PC. Also, add a checksum at the end.
I've done stuff like this with a simple binary format
struct PacketHdr
{
char syncByte1;
char syncByte2;
char packetType;
char bytesToFollow; //-or- totalPacketSize
};
struct VoltageSet
{
struct PacketHdr;
int16 channelId;
int16 voltageLevel;
uint16 crc;
};
struct VoltageResponse
{
struct PacketHdr;
int16 data[N]; //Num channels are fixed
uint16 crc;
}
The sync bytes are less critical in a synchronous protocol than in an asynchronous one, but they still help, especially when the embedded system is first powering up, and you don't know if the first byte it gets is the middle of a message or not.
The type should be an enum that tells how to intepret the packet. Size could be inferred from type, but if you send it explicitly, then the reciever can handle unknown types without choking. You can use 'total packet size', or 'bytes to follow'; the latter can make the reciever code a little cleaner.
The CRC at the end adds more assurance that you have valid data. Sometimes I've seen the CRC in the header, which makes declaring structures easier, but putting it at the end lets you avoid an extra pass over the data when sending the message.
The sender and reciever should both have timeouts starting after the first byte of a packet is recieved, in case a byte is dropped. The PC side also needs a timeout to handle the case when the embedded system is not connected and there is no response at all.
If you are sure that both platforms use IEEE-754 floats (PC's do) and have the same endianness, then you can use floats as the data type. Otherwise it's safer to use integers, either raw A/D bits, or a preset scale (i.e. 1 bit = .001V gives a +/-32.267 V range)
Adam Liss makes a lot of great points. Simplicity and robustness should be the focus. Human readable ASCII transfers help a LOT while debugging. Great suggestions.
They may be overkill for your needs, but HDLC and/or PPP add in the concept of a data link layer, and all the benefits (and costs) that come with a data link layer. Link management, framing, checksums, sequence numbers, re-transmissions, etc... all help ensure robust communications, but add complexity, processing and code size, and may not be necessary for your particular application.
USB bus will answer all your requirements. It might be very simple usb device with only control pipe to send request to your device or you can add an interrupt pipe that will allow you to notify host about changes in your device.
There is a number of simple usb controllers that can be used, for example Cypress or Microchip.
Protocol on top of the transfer is really about your requirements. From your description it seems that simple synchronous protocol is definitely enough. What make you wander and look for additional approach? Share your doubts and we will try to help :).
If I wasn't expecting to need to do efficient binary transfers, I'd go for the terminal-style interface already suggested.
If I do want to do a binary packet format, I tend to use something loosely based on the PPP byte-asnc HDLC format, which is extremely simple and easy to send receive, basically:
Packets start and end with 0x7e
You escape a char by prefixing it with 0x7d and toggling bit 5 (i.e. xor with 0x20)
So 0x7e becomes 0x7d 0x5e
and 0x7d becomes 0x7d 0x5d
Every time you see an 0x7e then if you've got any data stored, you can process it.
I usually do host-driven synchronous stuff unless I have a very good reason to do otherwise. It's a technique which extends from simple point-point RS232 to multidrop RS422/485 without hassle - often a bonus.
As you may have already determined from all the responses not directly directing you to a protocol, that a roll your own approach to be your best choice.
So, this got me thinking and well, here are a few of my thoughts --
Given that this chip has 6 ADC channels, most likely you are using Rs-232 serial comm (a guess from your question), and of course the limited code space, defining a simple command structure will help, as Adam points out -- You may wish to keep the input processing to a minimum at the chip, so binary sounds attractive but the trade off is in ease of development AND servicing (you may have to trouble shoot a dead input 6 months from now) -- hyperterminal is a powerful debug tool -- so, that got me thinking of how to implement a simple command structure with good reliability.
A few general considerations --
keep commands the same size -- makes decoding easier.
Framing the commands and optional check sum, as Adam points out can be easily wrapped around your commands. (with small commands, a simple XOR/ADD checksum is quick and painless)
I would recommend a start up announcement to the host with the firmware version at reset - e.g., "HELLO; Firmware Version 1.00z" -- would tell the host that the target just started and what's running.
If you are primarily monitoring, you may wish to consider a "free run" mode where the target would simply cycle through the analog and digital readings -- of course, this doesn't have to be continuous, it can be spaced at 1, 5, 10 seconds, or just on command. Your micro is always listening so sending an updated value is an independent task.
Terminating each output line with a CR (or other character) makes synchronization at the host straight forward.
for example your micro could simply output the strings;
V0=3.20
V1=3.21
V2= ...
D1=0
D2=1
D3=...
and then start over --
Also, commands could be really simple --
? - Read all values -- there's not that many of them, so get them all.
X=12.34 - To set a value, the first byte is the port, then the voltage and I would recommend keeping the "=" and the "." as framing to ensure a valid packet if you forgo the checksum.
Another possibility, if your outputs are within a set range, you could prescale them. For example, if the output doesn't have to be exact, you could send something like
5=0
6=9
2=5
which would set port 5 off, port 6 to full on, and port 2 to half value -- With this approach, ascii and binary data are just about on the same footing in regards to computing/decoding resources at the micro. Or for more precision, make the output 2 bytes, e.g., 2=54 -- OR, add an xref table and the values don't even have to be linear where the data byte is an index into a look-up table ...
As I like to say; simple is usually better, unless it's not.
Hope this helps a bit.
Had another thought while re-reading; adding a "*" command could request the data wrapped with html tags and now your host app could simply redirect the output from your micro to a browser and wala, browser ready --
:)