I've did research and still can't figure this out, but I know the problem. The problem is that Eazfuscator isn't installed on other peoples pc, but how would I get them to run it without getting this error, and without them installing eazfuscator? Or should I use another one?
Error when running protected application:
This application has been built with an evaluation version of Eazfuscator.NET, and therefore cannot be distributed. You can install Eazfuscator.NET on this computer to be able to run this application.
You need to purchase a developers license plain and simple. Until then they will see this message. When you get the license and compile the application this wont happen...
More about it here...
http://www.gapotchenko.com/eazfuscator.net/purchase
Related
I'm developing a program on Widows10 with Qt. If I run it from the command line, it exits silently, immediately. When I try to debug it, a dialog box is displayed saying "During startup program exited with code 0xc0000139."
I know this means that Windows failed to load one or more DLLs.
How do I find which DLLs they were?
Ideally, I would prefer not to download any additional utilities beyond what is provided by Windows10 and Qt.
For what it's worth I resolved my problem.
It turned out the the program I was trying to run hadn't been rebuild since my last set of changes. I'm unsure why that was so, clearly my own error but I'm not sure what, precisely.
For the benefit of anyone coming here trying to find an answer to the question at the top of the page, if you have cygwin or another Unix-alike on your system, ldd is a good program with which to start looking through the sharable images you link to.
I have a radio button that is represented as a pbdatawindow, when I run setcelldata to pick an option it works fine on my laptop but fails on my colleagues laptop. If we try the run the command again on my colleagues laptop we get a fatal error from UFT.
The only difference between my UFT install and my colleagues is that my colleagues version is installed in French. Has anyone seen a similar issue?
PbWindow().PbDataWindow().SetCellData 1,1,""
Few things to try:
What version of uft are you using? - perhaps check for newer of see if there is a patch available?
Jump onto the microfocus knowledge base and see if there is anything around power builder.
You say the machines are the same but does that include every application too? In the past I've known that if you install applications after uft it can break its references. Try uninstalling and reinstalling uft. There is a repair option but uninstall/reinstall is normally more thorough.
Try and clear out all your temp and user settings.
In your user profile backup then remove all folders with mercury, hp, Hewlett-Packard and microfocus.
-The go to %temp% and clear evetything.
Try and pin down the problem - Has your colleague tried the English version or uft? - if that works, is it an option? (everyone use the same version)
If it doesn't work it suggests it's your colleague's machine as opposed to uft.
Is evetything such as the resolution and browser/application versions the same? Or simply try another French localised machine?
What's the fatal error? Does it provide any clues on why it failed?
Finally, You're paying a lot for commercial software. Don't suffer in silence :-)
Log a support call with microfocus. It's a bit long winded but Back in the day they used to be pretty good at helping. They'll ask you for logs and knowing how to get that is good to know.
There's more to try - let me know how you get on.
How can I solve this error when the application is published:
You probably have just installed it, but you've done it running the setup from a different location.
Uninstall the application and run again the setup. Remember to run the setup from the same location when you update it.
I'm not 100% sure about it, but form my experience it's correct.
I'm following the instructions here but it seems not to work. I'll contact the developer, but wonder if someone has been able to make it work somehow.
The installation process is completed, but Netbeans doesn't see the plug-in. I assume it is deployed incorrectly.
Not sure how it got fixed but suddenly upon starting the IDE an update for the plugin showed up and it started working afterwards.
Can anyone help for the following ERROR:
Couldn't register com.india.XXX with the bootstrap server. Error: unknown error code.
This generally means that another instance of this process was already running or is hung in the debugger.
here m using xcode 4.1 and i have same project folders in my local desk.
When ever i open multiple projects with the same name its showing the above error.
Thanks in advance.
Some of the fixes that the links Saif contain may work for some, but not for me.
I have a very simple solution without restarting that will usually get you through the day.
When you get this error, before you do anything else, build for the other device (if you are running a universal application).
When you build for the other device, it kind of "overwrites" the process that creates this error. Once the other device is up and running, immediately build for the device that created the error. This will work most if not all the time, and will save you time digging through the multitude of fixes you will find in the other links.
I tried almost all of the fixes found there and none of them worked in my case. This works, but you should check your appDelegate for any bugs in your willEnter/didEnter (and other related methods).