I have a VBA Macro that I need to run on a CSV file that always has the same name and is always in the same location. Is there a way I can get it to automatically run the macro on the specified csv file as soon as the macro file is opened? Thanks in advance!
Yep, pop it in the Workbook_Open event. To do this open VBA, make sure you can see the Project Explorer, double click on ThisWorkbook, click the drop down that currently says General and change it to Workbook and put your code in there.
Related
Is there a way to have an Excel macro to check what file I double clicked on to open.
When I open that file, the Add-Ins installed load first, then the file I clicked on loads. How can I write code inside one of my Add-Ins to check what the filename is that I am trying to open?
I tackled this by using 2 instances of Workbook_Open inside an excel Addin.
When a file is loaded, the addin starts up, and checks to see if there are any active workbooks. If there is none, then we wait a little bit and check again, looped as many times as you deem necessary, or until there is a valid workbook open. This makes sure your computer has time to load up the excel file. Once there is an active workbook, we process it to make sure it is not the workbook of the addin. If it is, then we exit our code. If it isn't then we Do Stuff.
I solved 2 of my questions on this site with the same code that can be found HERE
Note: I left out the parts where I Do Stuff... because really it's there to do anything you want with it. The code in the link just does what the previous paragraph describes.
Is it possible to run a macro on web browser? I can open an excel in a browser but i am not sure if macro can run with it. And also, how am I going to enable it automatically within a browser?
If I am correct in assuming that you're asking if a vba macro can be run automatically after opening it from a link on a webpage rendered by a browser, the best way to do that is to set code to run automatically whenever the workbook linked in the webpage is opened.
To have a macro run when a workbook is opened double click the "ThisWorkbook" object in the vba project explorer of the workbook that has your code and add these lines of code
Private Sub Workbook_Open()
Call Module1.hello 'Change this line to start your code
End Sub
This automatically executes the sub "hello" in Module1 of the workbook.
Note that the user has to have Macros Enabled in their Trust Center Settings for anything to run.
Also note that depending on their browser and where the actual link points to the workbook file might have to be downloaded first and then opened from the download location for the macro to run.
I have written some code for an excel spreadsheet. This sub has been added to the ribbon using the standard customizations found in File -> Options -> Customize Ribbon. What is funny though, is that the customization will run the Sub on the EXACT EXCEL FILE that the Sub is written in, i.e. the original.
My users copy the excel file and make adjustments and then run the sub (by clicking the customized button in the ribbon), which then opens the ORIGINAL template file and runs the code. This actually works fine - and I like it because it runs the TEMPLATE code on the ACTIVE sheet. But the only problem is it is also OPENING the original template file. How do I get it to close? Remember it is not the ActiveSheet anymore.
One possible answer is to check if the template is open, then close it (using a static reference), but I would prefer something a little more elegant than that.
You should be able to find the template/original using ThisWorkbook.
Also, if you deliver your workbook's code as a .xlam instead of .xlsm, it will be opened, but there won't be a window for it, so users won't see it.
Not sure if you're using this already, but you might also want to use "for this workbook only" when adding ribbon buttons for a .xlam . (Delivering as .xlam allows you to install buttons from a workbook into the ribbon, without relying on file path and without needing your users to also install buttons (they install .xlam instead).)
I have added a toolbar menu for my macro, so I can just press the button and it runs my macro from any excel document. Every time I run the macro though, it opens the source file containing the macro. Is there a way that it won't open the source file and just run the macro? (even opening and closing wouldn't too much of an issue, but I'd prefer not opening it at all)
I haven't been able to find any information about this, so all help to get me started is appreciated.
You can't pull code out of the air to run it; Excel's going to have to open the file the code's stored in to run the code.
If I understand it correctly, you can create an Excel add-in from your code and have the add-in load automatically when Excel starts. Your code will always be available in that case.
This seems like a good place to start:
http://msdn.microsoft.com/en-us/library/aa140990(v=office.10).aspx
USE YOUR PERSONAL MACRO WORKBOOK
Open the VBEditor and find the module containing your macro.
Copy that code.
Now in the VBProject Panel on the left, locate your PERSONAL.XLS or PERSONAL.XLSB project. This is the project where you store macros you want available at all times. Add a module to that project and put your code into it.
Now update your "button" so that it points to the macro in that workbook and you're good to go.
On the off chance your PERSONAL.XLS project does not exist, use the macro recorder to record a "junk" macro and be sure to set it to "Store Macro In: Personal Macro Workbook"... that will create it for you the first time.
Stated simply my question is as follows Is it possible for a button on a worksheet in a normal excel workbook (.xlsx not .xlsm) to trigger a macro in another file specifically an installed excel add in (.xlam).
Here is some background on why I want to achieve this. I have a workbook that many users need to be able to view but only some need to be able to update by filling in a form on another sheet and calling a macro in an add in. The worksheet should not contain any macros to avoid security warnings when opened by normal users. I can do this by having a ribbon button in the add in that the user clicks which will then check that the correct workbook is open and that the form is filled in etc. before executing the update code. However the interface would be nicer if the button instead of appearing on the ribbon was on the worksheet just below the form. Therefore my question is it possible to trigger an external macro from a button click in a non macro enabled workbook.
Yes, you can assign an external macro (which should be .xlsm file) to a non-macro-enabled workbook (.xlsx) button. My xlsm macro resides in the same directory as the xlsx workbook for simplicity. (Note: I am using Excel 2010)
Firstly, you must open your xlsm macro in the same instance of Excel window (i.e. do not open a new instance of Excel) so that your xlsx workbook will be able to see/access it.
Right-click on your xlsx workbook button and select "Assign Macro..."
Make sure you select Macros in: All Open Workbooks
All macros in open workbooks will be shown (this is why it is important to do step 1).
Select the desired macro from the list then click OK.
I don't see how you can execute a macro from a control in a non-macro-enabled workbook.