I have created a small app with a storyboard.
Now, I have created a first view, which should be my splash. I am now searching for the right place to put my work into it. After this work, I would programmatically triggering a Storyboard Segue to switch to the next view. For this, I am searching the right place/event. It should be an event which is called right after the view will be shown.
I have tried viewDidLoad but it seems, that this event is triggered before the view is shown on the screen.
The (void)viewDidLoad method is called the 1st time the view is loaded.
So it's the good place where to write your init/setup lines.
The (void)viewDidAppear: method is called everytime your view is displayed.
Hope this helps.
Actually, and for a little nitpicking here. viewDidAppear is not called every time a VC is shown, but each time it is inserted in the VC hierarchy. So it seems to be what you want to use for now. But if you have later some use case where you want some action to take place each time the view is displayed to the user you need other means. For example this method will not be called when you push back some navigation VC (your VC is already in the hierarchy).
Related
I have an app I am working on that has a main screen with two buttons. One will take you to a view of a GPS (map) and then once there (new VC) it has options for setting that position or bringing up a list (tableview, another VC) of all locations already tagged.
At the list VC, if you click on the table cell, it will bring up the VC with the map. Problem is, this then adds the same VC bak on the stack. If a user clicks the Cancel button, they go back ones screen, then cancel goes back another screen, etc... until back to the main.
I know I can do the [self.navigationController popToRootViewControllerAnimated:YES]; to pop back to root but that is not always what I want.
Also, I know I can do: [[[self presentingViewController] presentingViewController] dismissModalViewControllerAnimated:YES];
I guess what I am saying is I want to "reuse" the GPS map view so I can call it from other VC's, so that is why I didn't go with the "pass back" to calling VC. So, is there away to either when a button is pressed and is to present a new VC, can I dismiss the prior one after the new one is shown? This way, a dismiss of current VC would take me back to where I need to be.
I hope makes sense and also that this question doesn't fall into the "Not an actual question" category.
Any help or better suggestions is greatly appreciated. Thx
Geo...
If you want to jump back some number of levels in a navigation controller's VC stack, you'll probably want to use its popToViewController:animated: method. To figure out if a particular view controller is on that stack, look at the navigation controller's viewControllers property. Be careful, though, as this kind of jumping around is a rather nonstandard UI behavior (even though there's API for it) which might confuse your users.
Also, using navigation controllers and presenting modally aren't the only ways to manage multiple view controllers -- you can always set the window's rootViewController yourself (and animate the change with UIView animations), even wrapping up your custom transition type in a custom UIStoryboardSegue if you like.
You can put a delegate in the table view. So that when a cell is pressed the info is passed to the delegate method in the VC which will dismiss the table view and reloads itself with the new info. You will have to implement refresh method in that VC.
I am working on an IPhone app that, through viewDidLoad, makes a connection and pulls data into a table. I would like the controller, or at least the table, to reload every time the controller is displayed, even if someone just switched from one tab to another or closed and re-opened the app on this controller. Is there a way to do this? I can't seem to find anything, it's also kind of a hard thing to search for. I have found discussions of when to put code in viewDidLoad but not another method that is run every them the controller displays.
Thanks,
Cheryl
You want to use
-(void)viewDidAppear:(BOOL)animated {
[super viewDidAppear:animated];
//code to reload table viewdata
}
Each time the view appears this method is called. I use this a lot in my app.
There's no way to do it by injecting code in only one place.
You can think of a workaround, like for example sending custom "reload request" notification from required parts of code:
viewDidAppear: in your view controller
applicationDidBecomeActive: (if table is presented)
tabBarController:didSelectViewController: (if switched onto controller with the table)
tabBar:didSelectItem: (same as above)
etc.
In you view controller simply observe this notification and reload data when required.
Although, whats more important: do you really need to reload data under such harsh requirements? In most cases data reload happens when
view controller's viewDidLoad: is called
it is manually initiated (button, for example)
long time passed since the last update was received
Otherwise it's just an overkill.
Essentially I have a view controller where the user picks from three choices. Once the user chooses something, the view segues away to another view controller that displays some information regarding their choice for about 5 seconds and then segues back to original view controller automatically where the User must make more choices... (its basically a loop until something is accomplished).
The problem I am having is when the User touches their option, it seems to just segue back to itself without ever displaying the intermediary screen. I added a sleep(5); to the viewDidLoad but all that causes it to do is pause on the original choice screen for 5 seconds before segueing to itself. I also put in an NSLog in just to make sure it was actually using the new controller, which it is indeed.
I didn't include code since its so trivial. viewDidLoad on the new controller, has sleep(5) and the call to segue back to the original view controller.
I solved the problem by moving the code to viewDidAppear. Should have done that from the beginning honestly, just didn't think it through enough I guess.
I've set up a really simple project using storyboards including two views as shown here: http://i.stack.imgur.com/iRx21.png. The navigation can be done by either selecting a cell in the custom table view or hitting the back button labelled with "<<". Everything works fine except the following:
when I switch between the views, every time an instantiation happens. The profiling shows an increasing number of view objects. I would like to keep only one of each view and instantiation should be happen only once. What am I doing wrong? (I'm using ARC.)
Thanks in advance!
You should not link your back button to the parent view controller. This is what causes the new instantiation.
The way to go is to embed the table view into UINavigationController (in IB, choose Editor -> Imbed In -> Navigation Controller. Then change your segue to a Push segue. You can of course hide the navigation bar etc. to make things look exactly as you like. Then, link the back button to the controller with an IBAction and in the handler do a simple
[self.navigationController popViewControllerAnimated:YES];
This would be the appropriate logic of what you are doing. Of course, you can also push the web view modally and then handle the button click with
[self dismissModalViewControllerAnimated:YES];
I have UITableViewController where I need to put initialization code only once to populate data source. in which method to put this code.
I tried with viewWillAppear: method, but it get executed every time view appear.
if you want to display things only once that the View has comed on screen, then yeah. go for it. Otherwise you also have ViewdidLoad or ViewWillAppear if you have to arrange things before the view begins the transition to slide in.
All of these methods will be executed every time from the tableView you tap on a row.
anyway the pattern you are trying to achieve is called singleton, you can find out about it more over here
What should my Objective-C singleton look like?
You can put it in viewDidLoad and it will be only once.
The - (void)viewDidLoad method is probably the place you want use. It gets called once the view controller has finished doing its loading code (either by loading a XIB or by calling loadView).