I have stellaris LM4f232 evaluation borad. I have ported free rtos , sysbios to stellaris lm4f232 board and successfully developed an gps tracking application . But I always wanted to port uc linux for my board . my question are
i) is there any material to port uclinux to any controller
ii)what are necessary knowledge I required to do the same
I have googled a lot . I did n't get the right information, but I have seen posts that its difficult ,but I cant able to realise the same .any help????
iii) what is the road map to achieve it , what are the knowledge I should need to achieve this
Linux, even uCLinux requires considerable memory resources; you'd want to start with at least 2Mb for the boot device and 16Mb of RAM (although a minimal system can be booted in as little as 4Mb). On a microcontroller, this means that you must have external memory.
Another issue is that Cortex-M devices are optimised to run code from on-chip Flash memory, having separate buses for ROM and RAM so that data and instructions can be fetched simultaneously. uClinux must run from external RAM, which has a detrimental effect on the performance, and you will be unlikely to achieve the 1.25MIPS per MHz figure the CM4 is otherwise capable of. It is possible to arrange for time critical code to be placed in on-chip flash is necessary, but it is of course a limited resource.
Some good advice on the issues of deploying Linux on a Cortex-M device can be found here
I would suggest to have a look on buildroot which as far as I know can be build for this board.
adding to #Clifford , you can use u-boot (bootloader) ,already configured for many boards ,if your board is not on list you can edit it.,
Related
I am working on Uboot bootloader. I have some basic question about the functionality of Bootloader and the application it is going to handle:
Q1: As per my knowledge, bootloader is used to download the application into memory. Over internet I also found that bootloader copies the application to RAM and then the application runs from RAM. I am confused with the working of Bootloader...When application is provided to bootloader through serial or TFTP, What happens next, whether Bootloader copies it to RAM first or whether it writes directly to Flash.
Q2: Why there is a need for Bootloader to copy application to RAM and then run the application from RAM? What difficulties we will face if our application runs from FLASH?
Q3: What is the meaning of statement "My application is running from RAM/FLASH"? Is it mean that our application's .text segment or .code segment is in RAM/FLASH? And we are not concerned about .bss section because it is designed to be in RAM.
Thanks
Phogat
When any hardware system is designed, the designer must consider where the executable code will be located. The answer depends on the microcontroller, the included memory types, and the system requirements. So the answer varies from system to system. Some systems execute code located in RAM. Other systems execute code located in flash. You didn't tell us enough about your system to know what it is designed to do.
A system might be designed to execute code from RAM because RAM access times are faster than flash so code can execute faster. A system might be designed to execute code from flash because flash is plentiful and RAM may not be. A system might be designed to execute code from flash so that it boots more quickly. These are just some examples and there are other considerations as well.
RAM is volatile so it does not retain code through a power cycle. If the system executes code located in RAM then a bootloader is required to obtain and write the code to RAM at powerup. Flash is non-volatile so execution can start right away at powerup and a bootloader is not necessary (but may still be useful).
Regarding Q3, the answer is yes. If the system is running from RAM then the .text will be located in RAM (but not until after the bootloader has copied it to there). If the system is running from flash then the .text section will be located in flash. The .bss section is variables and will be in RAM regardless of where the .text section is.
Yes, in general a bootloader boots the system, but it might also provide a mechanism for interrupting the default boot path and allow alternate firmware to be downloaded and run instead, as well as other features (like flashing).
Traditional rom had a traditional ram like interface, address, data, chip select, read/write, etc. And you can still buy rom that way, but it is cheaper from a pin real estate perspective to use something spi or i2c based, which is slower. Not desireable to run from, but tolerable to read once then run from ram. newer flash technologies can/have had problems with read-disturb, where if your code is in a tight loop reading the same instructions or for any other reason the flash is being read too fast, the charge can drop such that a read returns the wrong data, potentially causing the program to change course or crash. Also your PC and other linux platforms are used to copying the kernel from NV storage (hard disk) to ram and then running from there so the copy from flash to ram and run from ram has a comfort level, and is often faster than flash. So there are many potential reasons to not use flash, but depending on the system it may be possible to run from flash just fine (some systems the flash in question is not accessible directly and not executable, of course SOME rom in that system needed to be executable/bootable).
It simplifies the coding challenges if you program the flash with something that is in ram. You can create and debug the code one time that reads from ram and writes to flash and reads from flash and writes to ram. DONE. Now you can work on separate code that receives data from serial to ram, or from ram to serial. DONE. Then work on code that does the same over ethernet or usb or whatever DONE. You dont have to deal with inventing a protocol or solving the problem of timing. Flash writing is very slow, and even xmodem at a moderate speed can be way too fast, so you have to buffer that data in ram anyway, might as well make the tasks completely separate, instead of an xmodem or any other serial based flash loader with a big ram based fifo, just move the data to ram, then separately go from ram to flash. Same for other interfaces. It is technically possible to buffer the data and give the illusion of going from the download interface straight to flash, and depending on the protocol it is technically possible to hold off the sender so that as little as one flash page is required in ram before programming flash. With the older parallel flashes you could do something pretty cool which I dont think most people figured out. When you stop writing to the flash page for some known period of time the flash would automatically start to program that page and you have to wait for 10ms or something like that before it is done. What folks assumed was you had to program sequential addresses and had to get the new data for the next address in that period of time and would demand high serial port speeds, etc, the reality is you can pound the same address over and over again with the same data and the flash wont start to program the page, and the download interface can be infinitely slow. Serial flashes work differently and either dont need tricks or have different tricks.
RAM/FLASH is not some industry term. It likely means that .text is in rom (flash) and .data and .bss are in ram. A copy of the initial state of .data will probably be on flash as well and copied to ram before main() is called, likewise .bss will be zeroed before main() is called. look at crt0.S for most platforms in gnu sources (glibc, or is it gcc, I dont know) to get the gist of how the bootstrap works in a generic fashion.
A bootloader is not required to run linux or other operating systems, you dont NEED uboot, but it is quite useful. Linux is pretty easy, you copy the kernel and root file system, either set some registers or some tags in memory or both then branch to the entry point in the kernel and linux takes over from there. Because linux is so complicated it is desireable to have a complicated bootloader that can capitalize on high speed interfaces like ethernet (rather than being limited to serial or slower).
I would add something regarding your question Q2.
Q2: Why there is a need for Bootloader to copy application to RAM and then run the application from RAM? What difficulties we will face if our application runs from FLASH?
It is not only about having SPI or similar serial external code memory (which is not that often anyway).
Even the external ROM/FLASH/EPROM/ connected to the usual high speed parallel bus will will prevent a system from running on a maximum clock (with zero wait state) even on the relatively slow MCUs due to the external memory access time. You would need 10 ns FLASH access time for the 100 MHz clock, which is not so easy to get (if economically possible at all). And you would agree that 100 MHz is not such a brain spinning speed any more :-)
That is why many MCU/CPU architectures are doing tricks with reading multiply instructions at once, or having internal cash, or doing whatever was needed to compensate for a slow external code memory. Only most older 8-bit architectures can execute the code directly from the flash memory ('in place').
Even if your only code memory was the internal Flash, something need to be done to speed it up. Take a look for example at this article:
http://www.iqmagazineonline.com/magazine/pdf/v_3_2_pdf/pg14-15-18-19-9Q6Phillips-Z.pdf
It desribes how the ARM7 has incorporated something they called MAM (Memory Accelerator Module). It is a good read, and you will find some measures there to speed up the code memory access for the specific ARM7 arhitecture (goes for most others):
Limit maximum clock frequency (from 80 MHz to about 20 MHz for the example in the article)
Insert wait-cycles during flash accesses
Use an instruction cache
Copy the program code from flash to RAM
Obviously, if the instruction cache was not an option (too small, or the clock too high) you are really left only with execution from the RAM, after relocating the code there at the start up.
There is an option also to run only specific section of code from the RAM, which could be specified to the linker. For the DSP (Digital System Processing) systems, there was really no option to run from the EPROM/FLASH even in the old days with clock around only few tens of MHz, let alone now.
Another issue is debugging, the options for debugging the code placed in ROM, or even Flash, are very limited (you have to move section of the code to RAM to be able to set a break point on most systems).
Regarding Q2, one of the difficulties you may face executing from Flash is another code update. If you are executing from the same block of Flash you are trying to update, the system will crash. This depends on your system architecture (how your application and bootloader are organized in Flash) but may be particularly hard to avoid if you are trying to update the bootloader itself.
i am working on a project, where i would like to install an embedded system in a certain location , the system is provided with a camera , the system has to perform image processing functions on the images obtained from the camera.
The system must be attached with gps and gsm modules.
i am in the process of choosing the hardware needed, i am thinking of using a beagle board or FPGA , which one is more suitable for my application ? do you recommend other boards? do you know any gsm or gps modules that can be interfaced with these modules?
Thank you
If your image processing algorithms are too CPU intensive I'll suggest you consider FPGAs. Otherwise, Beagle board is fine.
What is the interface to your camera? USB / FireWire / I2C / other? If the Beagle Board supports what you need, and can handle the processing, that's probably the easiest way to go - FireWire and USB interfaces are not exactly trivial to do on an FPGA, unless you can get a board and a matching Linux distro for it, where everything is configured and working out of the box (and it's probably going to be expensive then...).
GPS modules typically connect over a simple serial connection, so that shouldn't be an issue for either solution.
I am a newbie starting out in micro-controller programming. The chip of interest here is cortex-a9. At reset or power up there has to be code at 0x0000000 from my readings. My questions though they may sound too trivial will help me in putting some concepts in perspective.
Does the memory address 0x0000000 reside in ROM?
What happens right after the code is read from that address?
Should there be some sort of boot-loader present & if so at what address should this be in & Should it also be residing in ROM?
Finally, at what point does the kernel kick in & where does the kernel code reside?
ARM sells cores not chips, what resides at that address depends on the chip vendor that has bought the ARM core and put it in their chip. Implementations vary from vendor to vendor, chip to chip.
Traditionally an ARM will boot from address zero, more correctly the reset exception vector is at address zero. Unlike other processor families, the traditional ARM model is NOT a list of addresses for exception entry points but instead the ARM EXECUTES the instruction at that address, which means you need to use either a relative branch or a load pc instruction. The newer cortex-m series, which are thumb/thumb2 only (they cannot execute ARM (32 bit) instructions) uses the traditional (non-ARM) like list of addresses, also the zero address is not an exception vector, it is the address to load in the stack pointer, then the second entry is reset and so on. Also the cortex-m exception list is different, that family has like 128 individual interrupts, where the traditional ARM has two, fast and normal. There is a recent cortex-m based question or perhaps phrased as thumb2 question for running linux on a thumb2 ARM. I think the cortex-m implementations are all microcontroller class chips and only have on chip memory in the tens of kbytes, basically these dont fall into the category you are asking about. And you are asking about cortex-a9 anyway.
A number of cores or maybe all of them have a boot option where the boot address can be 0x00000000 or something like 0xFFFF0000 as an alternate address. using that would be very confusing for ARM users, but it provides the ability for example to have a rom at one address and a ram at another allowing you to boot on power up from a rom then switch the exception table into ram for runtime operation. You probably have a chip with a core that can do this but it is up to the chip vendor whether or not to use these edge of the core features or to hardwire them to some setting and not provide you that flexibility.
You need to look at the datasheet/docs for the chip in question. Find out what the name of the ARM core is, as you mentioned cortex-a9. Ideally you want to know the rev as well r0p0 kind of a thing, then go to ARM's website and find the TRM, technical reference manual for that core. You will also want to get a copy of the ARM ARM, ARM Architectural Reference Manual. The (traditional) ARM exception vectors are described in the ARM ARM as well as quite a ton more info. You also need the chip vendors documentation, and look into their boot scheme. Some will point address zero to the boot prom on power up, then the bootloader will need to do something, flip a bit in a register, and the memory controller will switch address 0 to ram. Some might have address 0 always configured as ram, and some other address always configured as rom, lets say 0x80000000 for example, and the chip will copy some items from rom to ram for you before boot, or the chip may simply have the power up setting for the reset vector to be a branch to rom, then it is up to the bootloader to patch up the vector table. As many different schemes as you can think of, it is likely someone has tried it, so you have to study the chip vendors documentation or sample code to understand Basically the answer to your rom question, is it depends and you have to check with the chip vendor.
The ARM TRM for the core should describe, if any, the strap options on the core (like being able to boot from an alternate address), connect those strap options, if any, that are implemented by the vendor. The ARM ARM is not really going to get into that like the TRM. A vendor worth buying from though will have some of their own documentation and/or code that shows what their rom based boot strategy is.
For a system destined to be a linux system you are going to have a bootloader, some non-linux code (very much like the bios on your desktop/laptop) that brings up the system and eventually launches linux. Linux is going to need a fair amount of memory (relative to microcontroller and other well known ARM implementations), that ram may end up being sram or dram and the bootloader may have to initialize the memory interface before it can start linux up. There are popular bootloaders like redboot and uboot. both are significant overkill, but provide features for developers and users like being able to re-flash linux, etc.
ARM linux has ATAGs (ARM TAGs). You can use both the traditional linux command line to tell linux boot information like what address to find the root file system, and ATAGs. Atags are structures in memory that I think r0 or something like that is set to when you branch from the bootloader to linux. The general concept though is the chip powers up, boots from rom or ram, if prepares ram so that it is ready to use, linux might want/need to be copied from rom to ram, the root file system, if separate, might want to be copied to somewhere else in ram. ATAGs are prepared to tell arm where to decompress linux if need be, as well as where to find the command line and or where to find things like the root file system, some registers are prepared as passed parameters to linux and lastly the bootloader branches to the address containing the entry point in the linux kernel.
You have to have boot code available at the address where the hardware starts executing.
This is usually accomplished by having the hardware map some sort of flash or boot ROM to the boot address and start running from there.
Note that in micro controllers the code that starts running at boot has a pretty tough life - no hardware is initialized yet, and by no hardware I mean that even the DDR controllers that control the access to RAM are not working yet... so your code needs to run without RAM.
After the initial boot code sets enough of the hardware (e.g. sets the RAM chips, set up TLBs etc, program MACs etc.) you have the bootloader run.
In some systems, the initial boot code is just the first part of the boot loader. In some systems, a dedicated boot code sets things up and then reads the boot loader from flash and runs it.
The job of the boot loader is to bring the image of the kernel/OS into RAM, usually from flash or network (but can also be shared memory with another board, PCI buses and the like although that is more rare). Once the boot loader has the image of the kernel/OS binary in RAM it might optionally uncompress it, and hand over control (call) the start address of the kernel/OS image.
Sometime, the kernel/OS image is actually a small decompressor and blob of compressed kernel.
At any rate the end result is that the kernel/OS is available in RAM and the boot loader, optionally through the piggy back decompressor, has passed control to it.
Then the kernel/OS starts running and the OS is up.
I am new to the locating hardware side of embedded programming and so after being completely overwhelmed with all the choices out there (pc104, custom boards, a zillion option for each board, volume discounts, devel kits, ahhh!!) I am asking here for some direction.
Basically, I must find a new motherboard and (most likely) re-implement the program logic. Rewriting this in C/C++/Java/C#/Pascal/BASIC is not a problem for me. so my real problem is finding the hardware. This motherboard will have several other devices attached to it. Here is a summary of what I need to do:
Required:
2 RS232 serial ports (one used all the time for primary UI, the second one not continuous)
1 modem (9600+ baud ok) [Modem will be in simultaneous use with only one of the serial port devices, so interrupt sharing with one serial port is OK, but not both]
Minimum permanent/long term storage: Whatever O/S requires + 1 MB (executable) + 512 KB (Data files)
RAM: Minimal, whatever the O/S requires plus maybe 1MB for executable.
Nice to have:
USB port(s)
Ethernet network port
Wireless network
Implementation languages (any O/S I will adapt to):
First choice Java/C# (Mono ok)
Second choice is C/Pascal
Third is BASIC
Ok, given all this, I am having a lot of trouble finding hardware that will support this that is low in cost. Every manufacturer site I visit has a lot of options, and it's difficult to see if their offering will even satisfy my must-have requirements (for example they sometimes list 3 "serial ports", but it appears that only one of the three is RS232, for example, and don't mention what the other two are). The #1 constraint is cost, #2 is size.
Can anyone help me with this? This little task has left me thinking I should have gone for EE and not CS :-).
EDIT: A bit of background: This is a system currently in production, but the original programmer passed away, and the current hardware manufacturer cannot find hardware to run the (currently) DOS system, so I need to reimplement this in a modern platform. I can only change the programming and the motherboard hardware.
I suggest buying a cheap Atom Mini-ITX board, some of which come with multi - 4+ RS232 ports.
But with Serial->USB converters, this isn't really an issue. Just get an Atom. And if you have code, port your software to Linux.
Here is a link to a Jetway Mini-Itx board, and a link to a 4 port RS232 expansion module for it. ~$170 total, some extra for memory, a disk, and a case and PSU. $250-$300 total.
Now here is an Intel Atom Board at $69 to which you could add flash storage instead of drives, and USB-serial converters for any data collection you need to do.
PC104 has a lot of value in maximizing the space used in 19" or 23" rackmount configurations - if you're not in that space, PC104 is a waste of your time and money, IMHO.
The BeagleBoard should have everything you need for $200 or so - it can run Linux so use whatever programming language you like.
A 'modern' system will run DOS so long as it is x86, I suggest that you look at an industrial PC board from a supplier such as Advantech, your existing system may well run unchanged if it adheres to PC/DOS/BIOS standards.
That said if your original system runs on DOS, the chances are that you do not need the horsepower of a modern x86 system, and can save money by using a microcontroller board using something fairly ubiquitous such as an ARM. Also if DOS was the OS, then you most likely do not need an OS at all, and could develop the system "bare-metal". The resources necessary just to support Linux are probably far greater than your existing application and OS together, and for little or no benefit unless you intend on extending the capability of the system considerably.
There are a number of resources available (free and commercial) for implementing a file system and USB on a bare-metal system or a system using a simple real-time kernel such as FreeRTOS or eCOS which have far smaller footprints than Linux.
The Windows embedded site ( http://www.microsoft.com/windowsembedded/en-us/default.mspx )
has a lot of resources and links to hardware partners, distributors and development kits. There's even a "Spark" incubation project ( http://www.microsoft.com/windowsembedded/en-us/community/spark/default.mspx )
What's also really nice about using windows ce is that it now supports Silverlight as a development environment.
I've used the jetway boards / daughter cards that Chris mentioned with success for various projects from embedded control, my home router, my HTPC front end.
You didn't mention what the actual application was but if you need something more industrial due to temperature or moisture constraints i've found http://www.logicsupply.com/ to be a good resource for mini-itx systems that can take a beating.
A tip for these board is that given your minimal storage requirements, don't use a hard drive. Use an IDE adapter for a compact flash card as the system storage or an SD card. No moving parts is usually a big plus in these applications. They also usually offer models with DC power input so you can use a laptop like or wall wart external supply which minimizes its final size.
This http://www.fit-pc.com/web/ is another option in the very small atom PC market, you'd likely need to use some USB converters to get to your desired connectivity.
The beagle board Paul mentioned is also a good choice, there are daughter cards for that as well that will add whatever ports you need and it has an on board SD card reader for whatever storage you need. This is also a substantially lower power option vs the atom systems.
There are a ton of single board computers that would fit your needs. When searching you'll normally find that they don't keep many interface connectors on the processor board itself but rather you need to look at the stackable daughter cards they offer which would provide whatever connections you need (RS-232, etc.). This is often why you see just "serial port" in the description as the final physical layer for the serial port will be defined on the daughter card.
There are a ton of arm based development boards you could also use, to many to list, these are similar to the beagle board. Googling for "System on module" is a good way to find many options. These again are usually a module with the processor/ram/flash on 1 card and then offer various carrier boards which the module plugs into which will provide the various forms of connectivity you need.
In terms of development, the atom boards will likely be the easiest if your more familiar with x86 development. ARM is strongly supported under linux though so there is little difficulty in getting these up and running.
Personally i would avoid windows for a headless design like your discussing, i rarely see a windows based embedded device that isn't just bad.
Take at look at one of the boards in the Arduino line, in particular the Arduino Mega. Very flexible boards at a low cost, and the Mega has enough I/O ports to do what you need it to do. There is no on-chip modem, but you can connect to something like a Phillips PCD3312C over the I2C connector or you can find an Arduino add-on board (called a "shield") to give you modem functionality (or Bluetooth, ethernet, etc etc). Also, these are very easy to connect to an external memory device (like a flash drive or an SD card) so you should have plenty of storage space.
For something more PC-like, look for an existing device that is powered by a VIA EPIA board. There are lot of devices out there that use these (set-top boxes, edge routers, network security devices etc) that you can buy and re-program. For example, I found a device that was supposed to be a network security device. It came with the EPIA board, RAM, a hard drive, and a power supply. All I had to do was format the hard drive, install Linux (Debian had all necessary drivers already included), and I had a complete mini-computer ready to go. It only cost me around $45 too (bought brand new, unopened on ebay).
Update: The particular device I found was an EdgeSecure i10 from Ingrian Networks.
I have been tasked to write a device driver for an embedded device which will communicate with the micro controller via the SPI interface. Eventually, the USB interface will be used to download updated code externally and used during the verification phase.
My question is, does anyone know of a good reference design or documentation or online tutorial which covers the implementation/design of the USB protocol stack/device driver within an embedded system? I am just starting out and reading through the 650 page USB v2.0 spec is a little daunting at the moment.
Just as a FYI, the micro controller that I am using is a Freescale 9S12.
Mark
Based upon goldenmean's (-AD) comments I wanted to add the following info:
1) The embedded device uses a custom executive and makes no use of a COTS or RTOS.
2) The device will use interrupts to indicate data is ready to be retrieved from the device.
3) I have read through some of the docs regarding Linux, but since I am not at all familiar with Linux it isn't very helpful at the moment (though I am hoping it will be very quickly).
4) The design approach, for now at least, it to write a device driver for the USB device then a USB protocol layer (I/O) would reside on top of the device driver to interpret the data. I would assume this would be the best approach, though I could be wrong.
Edit - A year later
I just wanted to share a few items before they vanish from my mind in case I never work on a USB device again. I ran into a few obstacles when developing code and getting it up and running for the first.
The first problem I ran into was that when the USB device was connected to the Host (Windows in my case) was the host issues a Reset request. The USB device would reset and clear the interrupt enable flags. I didn't read the literature enough to know this was happening, thus I was never receiving the Set-Up Request Interrupt. It took me quite a while to figure this out.
The second problem I ran into was not handling the Set-Up Request for Set_Configuration properly. I was handling it, but I was not processing the request correctly in that the USB device was not sending an ACK when this Set-Up Request came in. I eventually found this out by using a hardware USB protocol analyzer.
There were other issues that I ran into, but these were the two biggest ones that took me quite a while to figure out. The other issue I had to worry about is big-endian and little-endian, Freescale 9S12 vs USB data format (Intel), respectively.
I ended up building the USB device driver similar to UART device drivers I had done in the past. I have posted the code to this at the following URL.
http://lordhog.wordpress.com/2010/12/13/usb-drive
I tend to use structures a lot, so people may not like them since they are not as portal as using #defines (e.g., MAX3420_SETUP_DATA_AVAIL_INT_REQR 0x20), but I like them since it makes the code more readable for me. If anyone has questions regarding it please feel free to e-mail and I can try to give some insight to it. The book "USB Complete: The Developer's Guide" was helpful, so long as you knew what areas to concentrate on. This was a simple application and only used low-speed USB.
While writing a device driver for any interface (USB, Parallel port, etc...) the code needed to be developed would depend upon whether there is any Operating System(OS), RTOS running on that Processor/Micro controller.
e.g. if thats going to run say WinCE - It will have its own Driver development Kit , and steps to be followed in the device driver development. Same for any other OS like Linux, symbian.
If its going to be a plain firmware code(No OS) which is going to control the processor/microcontroller, then it's a different situation altogether.
So based on either of the above situation u are in, one needs to read & understand:-
1.) The Hardware Specification of the processor/micro controller development board - Register files, ports, memory layout, etc.
2.) USB spec
3.) Couple of pointers i found quickly. Google shud be ur friend!
http://www.lrr.in.tum.de/Par/arch/usb/usbdoc/ - Linux USB device driver
http://www.microsoft.com/technet/archive/wce/support/usbce.mspx
-AD
I've used an earlier edition of USB Complete by Jan Axelson. Indeed very complete.
From the editorial review:
Now in its fourth edition, this developer's guide to the Universal Serial Bus (USB) interface covers all aspects of project development, such as hardware design, device firmware, and host application software.
I'm curious, why did you pick the 9S12? I used it at a previous job, and was not pleased.
It had lousy gcc support so we used Metrowerks
which may have been okay for C, but often generated buggy C++
had a lousy IDE with binary project files!
The 9s12 was also slow, a lot of instructions executed in 5 cycles.
Not very power efficient, either.
no barrel shifter, made operations that are common in embedded code slow
not that cheap.
About the only thing I dislike more is an 8051. I'm using an ARM CortexM3 at my current job, it's better than a 9S12 in every way (faster clock, more work done per clock, less power consumption, cheaper, good gcc support, 32-bit vs. 16-bit).
I don't know which hardware you're planning to use but assuming that's flexible, STMicro offers a line of microcontrollers with USB/SPI support and a library of C-code that can be used with their parts. -- I've used their ARM7 series micros for years with great success.
Here is an excellent site maintained by Jonathan Valvano, a professor at the University of Texas. He teaches four courses over there (three undergraduate, one graduate), all are about using a 9S12 microcontroller. His site contains all the lecture notes, lab manuals, and more importantly, starter files, that he uses for all his classes.
The website looks like it's from the 90's, but just dig around a bit and you should find everything you need.
users.ece.utexas.edu/~valvano/
Consider AVR for your next MCU project because of it's wonderful LUFA and V-USB libraries.
I'm working on a project using the Atmel V71. The processor is very powerful and among lot's of high end connectivity offered on chip is a USB engine that will do device or host modes for 480 Mhz or 48Mhz (not USB 3.0). The tools are free and come with a number of host and device USB example projects with all the USB stack code right there. It supports 10 end points and all the transfers are done via DMA so you have most of the processor horsepower available for other tasks. The Atmel USB stack works without needing an RTOS