I would like to know if there is a program for analyzing traffic through USB. For example, I would like to know what files are transmitted from the computer to the device at the moment, what he does with the device. I need it to debug device, not driver! Is there such a program?
I think you can use this site as a starting point and inspect the different methods in detail on your own.
wireshark wiki
Related
I have a project based on a Nucleo H743ZI2 board that communicates with a PC through the USB OTG port on the Nucleo.
Everything is working fine as long as, weirdly enough, I have the STlink USB cabled plugged in (which I have been using to work on the firmware, flash, debug, etc).
However, today I was getting ready to do actual tests with this project and used an external power source to power the H7. I initially tried a 3.3V external source which is available from one of the shields, and then tested a lab PSU at both 3.3V. Thinking it could be PSU related I also tried external 5V with the same results.
Basically, the device is not recognized by the computer operating system, unless the STlink USB is plugged in.
I can't really put my finger on this one; I initially thought it was a PSU related issue (that nucleo board has some restrictions when it comes to using external power sources) but at this point I am fairly confident I am failing to initialize something in my code. Not sure what though.
I'd be happy to share with my code, but wouldn't know where the start. I haven't done much as far as the USB OTG is concerned other than modifying the receive callback to process the data.
Any idea what I might be missing here?
Cheers
On reading many websites, I got confused.
Is the USB driver essential for making the device work? Or is it essential for making it communicate with the OS to do functions such as printing and doing other OS stuff?
To explain my question more clearly -
I am working on developing a USB device, that will communicate with the software i will write.
Do I need to develop a driver for such a system?
or
Do I just need the software program to send the proper messages to the device?
I am assuming your micro controller will be a USB device and your PC will be USB host.
The below diagram is the SW architecture for USB host. Now since your host is a PC, you do not need to worry about any part except the application at the top.
So lets talk about the device. What you need is a device stack which resembles with the host stack below. You can get the device stack easily and port it in your micro controller. But I suppose you need an application in your device too same as the top box of the below diagram which will understand the requests from the host and service the request.
So basically what I am saying that you need two applications and the rest of the components you can get it with some effort.
Regards.
I have a weird question. I would like to make a virtual copy of a device. In order to test some software I want to make a mirror copy of a particular scanner. Now I know there are some virtual TWAIN scanners out there, but I want Windows to recognise it as a particular brand and type just so I can test the particular software that comes with it.
I.e. I have an HP scanner plugged in, I want to make a mirror copy of it, unplug it and windows will still detect it as plugged in and operating normally so I can open the scanner software and driver. My goal is to make this virtual device stick, even on reboot. Is there any way this can be achieved? I'm happy to load the device data on an USB drive if that works as workaround.
I hope you guys can help me!
Cheers,
Jasper
You probably could do that by writing your own kernel-mode Windows driver that pretends to be a USB hub and pretends that it has a device plugged in to it which is a virtual scanner. Writing Windows drivers usually involves a lot of arcane C programming and it is unlikely that anyone will be able to tell you everything you need to do on this type of site.
For testing purposes I need to power off a USB device from my computer programmatically. The microprocessor in the USB device is ARM Cortex M4.
I have tried using Devcon, although the device was disabled, power was still provided to the device.
I have also tried to disable the USB root hubs ,that also didn't work.
I have read some other posts indicating that a SSR could be used, this option is not desired. I would rather choose the software solution(if there is one of course).
Some other answers have indicated that this is an OS issue, and some others a chip-set architecture issue.
So my question is what options are there available. And also is this purely something dependent on the computer side or do we need to implement something on the USB device side as well.
Thank you in advance.
Preferably, this would be a computer connected via cable, but if there's a way to do it over wifi then this would also be useful. I'm wondering if it's possible to send messages between them?
Or if i had a mac app and an iPhone app, could I communicate between them over wifi or a usb connection, rather than using a server or something?
Connecting over WiFi is possible, cable connection however isn't possible (certainly not in the documented API) unless the phone is jailbroken.
For wifi you're just going to connect to a TCP/IP host/socket. Have a look at CocoaAsyncSocket. The computer would need to be hosting some sort of server software. This is how iTunes Remote and AirMouse work.
There are some "permitted" (non-cracked phone) ways to send data to the iPhone from a device that's physically plugged in. There are several barcode readers - like the Linēa-pro used in US Apple stores - and magstripe readers for credit cards (e.g., the Macally Quikswipe) that can send limited amounts of data to/from the iPhone.
If your computer is a small embedded device and your data requirements are meager, it may be possible.