I am trying to connect mysql database with mulesoft database connector, but it is giving error while I do test Connection. I am not able to figure out what is wrong I am doing. Could you please put me in right direction?
Please ask for more information you need from me.
The problem you are facing is not because of Mule component.There may be several other reasons at MySQL side.
As you can see that your credentials are processed by MySQL however denied.This suggests that the problem may not be directly
related with credentials because if credentials were wrong the error would have been different then denied.
When credentials are denied, the problem is mostly related with:
Permission issue - Solution >> Grant permission to use "db_name" from "Localhost"
Your connection string looks fine but sometimes string encoding result this error
Some installed components are interfering with MySql -> Check the components installation
Also
LOCALHOST and "machine name" aren't the same to MySQL.
I'd check from the command line that you can connect to localhost:
mysql --user=<user_name> --password db_name
Enter password: your_password
If it fails, connect and run this with the appropriate permissions:
create user db_name#localhost identified by 'db_name';
grant select on <user_name>.* to db_name#localhost;
Never mind :) I found the solution although did not find what the problem was only suspecting that the root was not having any schema privileges ( as shown by MySQL Workbench GUI).
Earlier I was using command line with which I am not well versed; after struggling a little I downloaded MySQL workbench and added one more user with all administrative and schema privileges and used that to connect with Database connector and God Damn!! it's working.
Related
I'm using Spring application and stack is like: Java 11, Spring Boot 2.2.1.RELEASE.
(technology versions may vary here)
When I try to connect to the database via Data Source using Intellij IDEA, I get always the issue like:
The specified database user/password combination is rejected:
[28P01] FATAL: password authentication failded for user 'postgres'
How can I fix it?
To be noticed: this answer is similar, but not related to:
Unable to connect from Intellij to mySql running in docker container - "specified database user/password combination is rejected"
To fix it:
you need to check your application.properties file and change the value of user password on line:
spring.datasource.password=your_password
The cause of issue is:
your value of the property spring.datasource.password in application.properties
does not match the user password what was selected by default during installing your database system.
E.g. more specifically on the step "Enter the password for the database superuser (postgres)":
To clarify: provided example is for PostgreSQL, but it can be another database system.
Edit: this assumes you run Linux
if the other answer provided by invzbl3 doesn't work, check out this solution, it worked for me. Make sure to restart afterwards.
https://docs.fedoraproject.org/en-US/quick-docs/postgresql/#_initial_configuration
If you’re getting ident errors from your app you’ll probably need to perform the accepted solution described at https://serverfault.com/questions/406606/postgres-error-message-fatal-ident-authentication-failed-for-user?newreg=a4fdc3e21349449985cc65b82399c5b4
(if you don't have nano, just use any other text editor)
sudo nano /var/lib/pgsql/data/pg_hba.conf
and edit host all all 127.0.0.1/32 ident to host all all 127.0.0.1/32 md5.
This should allow most applications to connect with username/password.
I am trying to installing RCU for Oracle Repository Creation utility however everytime I try to install the development repository it runs on error.
Steps to reproduce the issue.
I run rcu bat file
Create repository/system load and product load
3.Choose oracle as database type/hostname localhost, port 1521 servicename xe, username sys and the password (I am able to login into oracle database with this login information) (I am using oracle 18c express
I am using the prefix dev
I am adding password for schemas, supervisor, and for the repository user.
I am not touching the tablespaces
I start the install and several error messages are dropping. like
Ora-65096 invalid common user or role name
Ora-01917 DEV_STB user does not exists
Ora-00955 The name has already been in use by another object.
My question what could be the problem with the installation of RCU and How can I resolve the issue ?
Funny thing is I am trying to install odi and RCU based on step by step video still something went wrong...
The issue here is you are logging to CDB with the service name XE. You need to log into the PDB (Plugable database).
Just change the service name from XE to XEPDB1 while connecting to the DB through RCU and your issue should be resolved.
im using oracle sql developer to make my database, but now i stopped to work.
it wrote this:
An error was encountered performing the requested operation:
Listener refused the connection with the following error: ORA-12514,
TNS:listener does not currently know of service requested in connect
descriptor
Vendor code 12514
i also tried to make new connection but it didnt help
pls help me,i dont know what to do, i need this to do my homework
when i tried to change connection it wrote this:
An error was encountered performing the requested operation:
ORA-01031: insufficient privileges
01031. 00000 - "insufficient privileges"
*Cause: An attempt was made to change the current username or password
without the appropriate privilege. This error also occurs if
attempting to install a database without the necessary operating
system privileges.
When Trusted Oracle is configure in DBMS MAC, this error may occur
if the user was granted the necessary privilege at a higher label
than the current login.
*Action: Ask the database administrator to perform the operation or grant
the required privileges.
For Trusted Oracle users getting this error although granted the
the appropriate privilege at a higher label, ask the database
administrator to regrant the privilege at the appropriate label. Vendor code 1031
Please check the services are running:
OracleOraDb11g_home1TNSListener and OracleServiceORCL.
You're going to have to do some troubleshooting; Here are a couple of suggestions:
ORA-12514 Tips
ORA-12514 TNS:listener does not currently know of service requested in connect descriptor
How to resolve error: ORA-12514
The service name ,you are using should be in sid column and not in service name entry box.
For example, the service name provided for you is overflow,you have to mention it in
ex:10.171.1.24:1521:overflow
Sid : overflow
Service : leave blank
Test the connection
Go to Services
check whether the "ORACLEServiceORCL" is running or not.
if not running then right-click on it and click start.
Your problem may solve this.
Happy coding :D
This worked for me- Close your SQL Developer and launch again.
I had the same issue after restarting my PC and could not access my local database. This fixed it.
Go to Run > services.msc > Services (Local) > OracleService
Right-click on OracleService > Properties > Log On
Make sure Local System Account is checked then press OK.
Stop the OracleService and restart it. It should be working now.
Mine was working fine till last night but this morning I found the said problem. I checked OracleOraDb11g_home1TNSListener and OracleServiceORCL was running and in "Started" status but still issue was there.
Just restarting both the services solved my issue. I suggest just try this once to save your time before exploring other solutions.
I have Openfire 3.7.1 installed on my Mac and have XAMPP installed aswell. I am having trouble configuring OpenFire. In the server settings I have given san-imac.local.lan as the domain name. The selected Standard database connection and picked MySql Database Driver. This is the databse URL jdbc:mysql://localhost:3306/test and given the username password of XAMPP phpmyadmin. But it says
A connection to the database could not be made. View the error message by opening the "/logs/error.log" log file, then go back to fix the problem.
First of all there is no such file in the /logs folder. What should I do to get this working and follow the procedures to get OpenFire up and running.
I need to build an app to connect to openfire for IM chatting like Gmail, Facebook, Yahoo using XMPP. If anybody could provide any guidance aswell, it will be very helpful.
Make Sure that your database is setup correctly including the name of your database, database username, and user's password. If you have this correctly configured then your opens ire should work just fine. Note that it will not accept if the database username has an empty password or not enough access rights to the database.
I hope that those hints will solve your problem.
check your password and username, I had the same error and it took me a while to figure out that I had my username wrong.
Resolved the issue.
log file is not getting created due to file write permission. To resolve this run OF server as follows
Run the openfire.sh file from terminal with sudo. This will start the OF with root access Now the error log file will be created.
My log file has error message as access denied to user #localhost. As I kept the user field blank in db connection page of openfire set up.
Keep the user field as root#localhost if u are using localhost.
As part of our product's installation process, a database is attached to the server.
We use EXEC sp_attach_db in order to attach it to MSSQL.
The problem occures when we try to attach it with "SQL Authentication" connection string - the database is attached to the server as read-only, thus preventing any write access from being performed
This is driving us nuts... it's working just fine with Windows Authentication, and the only difference is the connection string... I tried googling for it but no mention for such a scenario is found.
Any ideas anyone?
It's important to mention that the MDF/LDF physical files are not set with "ReadOnly" attribute, so this is not the problem.
I'm curious why you can't attach the database with write permissions and then just make the whole thing read only after the install?