I have recently finished my website and uploaded code to server. It is working perfectly when connected to Wi-fi or broadband connection.
But When i am connecting the site using 3G or LTE it's showing some default page. Exact domain is not loading.
Still not able to understand why it's happening.
My Domain name: http://www.jockdrive.com
Please help me with your suggestions.
There might be cached data stored on the server of the Interner Service provider. Normally, ISPs clear cached data every 24-48 hours (in rare cases 72). This is called propagation.
If you want to see an up-to-date and uncached version of your website, check it via proxy server. Here is the link: https://kproxy.com/
;QUESTION
www.jockdrive.com. IN AAAA
;ANSWER
www.jockdrive.com. 3600 IN AAAA 2607:f1c0:1000:80f9:71ce:7028:7b2e:b009
Your domain name is probably configured with wrong IPv6 address, and I guess cellular operators are using that as default when available. You can try deleting that record (or check with your hosting provider if they can provide the correct one) and see if it helps.
Related
A website prodecotech.com is hosted by Bluehost
Out of the blue last week my entire office could not access prodecotech.com the connection would time out.
However this is only the situation from one of our internet connections. If I switch over to a guest connection, or use a mobile connection, the website loads fine. The website also loads perfectly fine for ATT and BlueHost tech support.
Our network is configured as follows.
We have a 50MB Dedicated Fiber Connection from an ATT Managed Router. The managed router has 2 ports in use. 1 Port going to OUR router for Data traffic and 1 Port going to OUR switch for VOIP Traffic.
If I connect a laptop to OUR router managing data traffic and try to access prodecotech.com, I get the same results, the connection times out.
If I connect a laptop to the switch managing VOIP traffic, prodecotech.com loads fine.
If I use our guest wifi which is through Comcast, the website loads fine as well.
So the problem is isolated to the Data Portion of my network.
There has been no configuration changes on our router or the managed ATT router.
I thought perhaps somehow our IP got blacklisted by BlueHost, but BlueHost says this is not the case.
ATT support is able to reach the website through their managed router.
I'm utterly stumped.
Additionally, I also cannot access the FTP or CPANEL Server Status for this hosting, both time out as well.
TRACERT has been giving me the following results consistently:
Any Ideas?
In my case, it was due to the wrong MTU(maximum transmission unit) in the router's network configuration. When I changed MTU to 1452 it started working fine.
You should contact your service provider and ask for appropriate configuration settings.
I have a very weird problem.
We have a Hyper-V failover cluster, where some guest VMs start to show specific problems after a live migration.
In each case, the live migration mostly works, but after it has been migrated, we can't log into some software (our product WinGate) any more. The SSPI handshake succeeds, we can RDP to the image, so it's not networking.
But ADSI fails to open a search object to retrieve a user object, and gives error 8007203A.
Since networking is working, SSPI is working, obviously domain connectivity is working to some degree, but the ADSI failure is very perplexing.
Has anyone else seen this? I feel it's most likely a bug in Windows, but we have been seeing this for over 18 months now - since we set up the cluster.
P.s. all hosts and VMs are 2k12R2 fully patched.
P.p.s. all VM MACs are fixed.
OK, looks like I found the answer.
Problem is NLA reclassified the domain network adapter after a live migrate, and set it to an unidentified network. This then kicked in the firewall to block ADSI.
thanks to this blog I was able to force NLA to view the adapter as a domain adapter (by adding a domain DNS suffix to the adapter), and the problem is solved. Hope this helps someone else!
EasyRTC is a open source webRTC plugin used for many purpose.
My intention is to prepare a video chatting example using this. When I try this with same network connection (same wifi) it works like a charm, but when I try this with different wifi network its not working instead its through errors like
No usable STUN/TURN path -- in client end
undefined -- in initiator end.
Is there is any configuration I need to change to make this working.
Thanks in advance
Mtbikemike has called it.
The general experiment is trying using the demos at demo.easyrtc.com. They are backed by a turn server. If they work across networks and your own doesn't, then it's probably a challenging network that needs a turn server. Turn servers don't punch holes so much as they act as packet relays.
EasyRTC is an open source bundle of a signalling server, a Javascript client and some demonstration code, rather than a plugin. If you've got a firewall between you and the other party then you'll need a TURN server. We do have a TURN server backing the demo.easyrtc.com demos on our servers. We are working on putting together a paid TURN service specifically designed for EasyRTC. Should be available in the next month or so. For now you could look into using a TURN service from Xirsys or put up you own TURN server in the cloud or on your premise but outside the firewall.
Newbie programmer here. I'm building an app for an API that requires an IP address for authentication. Basically, users have to send the API management their IPs and then each time a computer makes a request to their server, it verifies whether it's coming from a registered IP.
Since I work in a number of different places and thus end up with different IPs, I thought it would be easiest to use DynDNS to establish a URL that points to whatever my current IP is and then send that URL to the API management. So my first question is if this approach would in fact work?
Secondly, assuming this would work, I set up ben.dynalias.com and downloaded the DynDNS Updater client. It appears to be working: the updater says status: OK and displays my current IP. However, when I navigate to the URL (ben.dynalias.com) there's no response. Should this be the case? How can I tell if it's working?
I don't see any reason it shouldn't work as long as your updaters aren't overwriting each other by running at the same time automatically from different locations.
You can ping ben.dynalias.com and see if your current ip matches.
I just hosted ben.dynalias.com and it gave me your IP.
Since there is no web server running on that IP, then your browser will not be able to show you a page result.
You can use http://www.kloth.net/services/nslookup.php
to check and see if you get the correct IP from a host lookup.
Depending on how often your IP changes this might not be a great solution as the DNS will cache your hostname and will not try and resolve it again until the TTL expires normally minimum 1 hour.
whether the API management accepts a hostname instead of an IP address is a question only they can answer. Some will, many won't as it's "easier" to hijack a domain name than to hijack an ip address.
trying to browse to you-address.dynalias.com that points to your own public address rarely works, even if you opened up the right ports because your router will be highly confused. The best way to test such a setup is by using a phone or tablet with 3g/GPRS internet - of course after you set up port forwarding in the router to point the appropriate port to your computer.
I am coding a mac app, which will be a server that serve files to each user's mobile device.
The issues with this of course are getting the actual ip/port of the server host, as it will usually be inside of a home network. If the ip/port changes, its no big as i plan to send that info to a middle-man-server first, and have my mobile app get the info from there.
I have tried upnp with https://code.google.com/p/tcmportmapper/ but even though I know my router supports upnp, the library does not work as intended.
I even tried running a TURN server on my amazon ec2 instance, but i had a very hard time figuring how what message to communicate with it to get the info i need.
I've been since last night experimenting with google's libjingle, but am having a hard time even getting the provided ios example to run.
Any advice on getting this seemingly difficult task accomplished?
The port of your app will not change. The IP change could be handled by posting your servers IP to a web service every hour or whatever time period you want.
Server should run a URL http://your-web-service.com/serverip.php?ip=your-updated-ip and then have your serverip.php handle the rest (put it into a mySQL db or something)
When your client start it should ask your site for the IP and then connect to your server with that.
This is a pretty common way of handling this type of things.