I am planning on doing a small arduino project and would like to know if what I'm thinking would work with a regular arduino board. I'm thinking of buying an Arduino Uno for my project, along with an IR LED and an IR sensor. So here's what I want to go with this:
I want to point the LED towards the sensor, so that the sensor is always detecting light. Then', I'll start "cutting" that light (say, with with my hand) several times. I want the arduino program to time the intervals between the times the light is "cut" and send these times to my computer via USB, so I can process this data.
I've seen many people talk about serial communication between an arduino board and a computer, but I'm not sure how that works. Will it use the same usb connector I use to upload programs to the board, or do I have to buy anything else?
EDIT: tl;dr: I guess my question, in the end, is twofold:
1) Am I able to "talk" to my computer using the built-in USB connector on the board, or is that used solely for uploading programs and I need to buy another one? and
2) Is this project feasible with an Arduino Uno board?
Thanks for the help!
Yes, your project is very feasible.
You use the built in USB connector to both program the device and communicate with it. Check out some examples on the Serial Reference Page
For reading the sensor, you'll want to use either a digital or analog input. For a digital input, you'll likely have to external components to control the light threshold, but it will provide a simple yes or no if something is in front of it. With an analog input, you can use a threshold in code to determine when your hand passes.
Timing can either be done on device with the Millis() function or on the connected computer.
Related
I am trying to create a space balloon. I need a way to track the balloon. I found a GPS Module with built-in antenna which is the GP-635T. However, after I set it up with the arduino, what is the code or what should I upload to the arduino so that it sends coordinates to the laptop without being connected via USB.
Here is the GPS Module:
https://www.sparkfun.com/products/11571
What you want to do doesn't involve merely programming the arduino. It will require you a radio or satellite transmitter to send out the coordinates to a matching receiver that can be connected to your PC to demodulate the radio signal and present the coordinate data through USB or serial interfaces. I'm sorry to say that, but unfortunately it seems to be a very expensive proposition and a bit hard for you to implement considering you seem not to know how to program the arduino yet or are aware of the additional hardware requirements and technical difficulties involved.
If you do happen to get a radio or satellite transmitter to go on the ballon and supply it with an adequate battery, the arduino part will be the easiest, just read the coordinate data from the serial port connected to your GPS module and relay it to the other serial port connected to your transmitter. Since you only have one hardware serial port on the arduino you'll have to use a software serial library for the other one.
A common hobbyist method to balloon tracking is to use the cellular phone system. Get a cellular module and have the Arduino text its location to your phone.
This obviously won't work in near-space but it's a cheap, long range system for balloon recovery once it gets closer to the ground. (Provided you are in an area with adequate cell phone service and not in the middle of a desert)
I have this samsung chip on a board (samsung s3c2510a) and I want to program to it via some method. However, I don't have a jtag reader on me and this board has a usb port. Is there any way to tell if I can program to the chip via this usb port? I ripped the board off a color laser printer by samsung and the board also has an ethernet connection.
Also, this board has 4 pins called "cn4 debug". Would this be of any use?
Here is a pic: http://imageshack.us/photo/my-images/262/img20120527120306.jpg/
Thanks,
Rohit
I doubt programing this board would even be posible. You could check if there is any software that is used to update the board (from the manufactuter) and try to reverse the protocol. You would also need to figure out the format of the firmware file. There is a lot of good stuff on hacking router firmware that may help. You should be able to find some mailing list to ask for help on.
For any device to be programmed over USB or indeed any port that is not part of the on-chip programming/debug architecture requires software/firmware supporting that port to be present on teh chip already. Some microcontrollers include ROM based primary bootloader code for this purpose. The S2C2510A has no such bootloader. But if the board already has software on it, part of it may indeed be a bootloader. However unless you can get information on the protocol used, you do not really have much hope.
A picture of the board does not really help; what you need is a full data sheet and/or schematic. You'll also want the data sheet and user reference manual for the chip itself. You don't really have much hope of making sense of this board without them. The board does not look like a development board to me, so board specific information may not be available.
CN4 merely means "Connector Number 4". Having just four pins it is likely that it is merely a connecting to the Console UART - a minimal low speed serial data peripheral on the S3C2510A.
I am working on Xilinx Spartan 3E platform, using this development board:
http://www.xilinx.com/products/boards-and-kits/HW-SPAR3E-SK-US-G.htm
My program operates on certain data and then provides output. I wish to transfer the input signals externally. The input data is a stream of 8-bit signals.
So, how do I send the input signals from my laptop to the FPGA via USB? Does Xilinx support this or is there standard software to do this?
Thanks.
It sounds like you are describing a uart more than a native USB interface. You can get a USB to logic level serial adapter that will let you easily transfer data to and from a Pc at up to 921.6k baud. A uart/serial port is easy to implement in the Fpga and PCs are easy to use with serial ports.
Here is the cable:
http://www.ftdichip.com/Products/Cables/USBTTLSerial.htm
If you have a development card it is very possible this type of interface is present.
On the software side you can use your programming language of choice as if it was interfacing with a seal port or use a terminal program like hyper terminal or Download teraterm http://ttssh2.sourceforge.jp/
Updated response:
100Hz is not a hard interface to make. At that rate you should use the serial interface if at all possible. The board you referenced has 2 full RS-232 connections. At that point you only need a way to connect that to your computer. If you have a PC with RS-232 connectors you only need a cable if you have a newer computer without you need a RS-232 to USB translator cable (like this one: http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=768-1014-ND or google rs232 usb). This will give you a virtual com port on the pc to interface with the previously mentioned terminal programs or your custom software.
Update 2:
on the resource tab of the development board page you linked to there are several UART based fpga designs that you should be able to use as a starting point.
i.e. the "PicoBlaze Processor SPI Flash Programmer".
That board doesn't provide easy access to the USB interface from the FPGA as far as I can tell. It's just for configuration and debug.
Some of the newer boards and tools do allow something called hardware-in-the-loop testing where the simulator can upload data to the FPGA, wait it to calculate the results and then pull the data back. This is relatively common when using Xilinx's System Generator product as the simulations can be really long.
But I think with that board you'd be better off using the on board RS232 port to get data to and from the board. You will have to build the infrastructure to do it yourself though.
This may also give you some ideas:
http://www.1pin-interface.com/
I have a Korg NanoKey which I'd like to use to control a simple synthesizer I've designed on the Arduino platform. (I have an Arduino Uno.) Basically, I don't care about MIDI, I just want to read what note the keyboard has pressed down, but if MIDI is the only way I can do that, then it's okay with me. So my big question is, how do I do this? I haven't been able to find anyone else on the Internet who has already done this.
But more specifically, I see two challenges: First, I'd like to plug my NanoKey directly into the Arduino's USB port, but then I'm wondering if the Arduino would provide the necessary power to the NanoKey. Second, I'm not sure what protocol I would be reading. Can I just read MIDI signals as described in this tutorial?
I don't want to curb your enthusiasm but what you're attempting might be a bit hard basket. A USB system consists of a host controller and one or more peripheral devices. It's the host that controls traffic flow to the devices which means that devices can't transmit data on the bus without an explicit request from the host controller.
I'm not familiar with either the nanoKey or the Arduino platform but I'd be fairly confident that the nanoKey is a USB "device", normally connected to a computer which would act as the host. So what you would need for this system to work is for the Arduino to act as the host when communicating with the nanoKey. The Arduino schematic shows that the Arduino Uno uses an ATmega8U2 for USB coms. Unfortunately the ATmega8U2 is a USB device, so you've got two peripheral devices but no host controller to facilitate the transfer of data between them. You'd be better off using a development board for a micro that provides either USB Host or USB On-the-Go.
I opened up a Korg Nano controller yesterday and was surprised to discover that there's an AVR mega32 inside. It would be a significant undertaking, but with a bit of work you could probably work out the schematic and reprogram it yourself using their programming header breakout. You might not end up with much more functionality than you've got this other way, but it would be very educational.
I agree with the Jono - you are biting off a lot - it might even end up easiest to hook the keys up to the Arduino directly - tearing out the electronics and figuring out a way to multiplex the keys into a single channel without losing polyphony (resistor 'ladder' maybe). I any case, good luck. Amusingly, you'd making an analog keyboard to plug into a digital synthesizer.
Quick and Dirty Arduino MIDI Over USB demonstrates how to send/receive MIDI out over USB, but unfortunately, this probably isn't any help for what you are trying to do, since he's found a way to send and receive MIDI signals from a USB host, not act as a USB host himself - the opposite of your problem. However, I thought perhaps it would be of use, if you ever wanted to control your device from a computer.
As mentioned in the other posts, you would need to use a separate chip to provide the USB Host interface. Here's a great guide to using the USB Host shield by Circuits#Home to interface with an Akai LPK25 (USB Midi Keyboard).
http://blog.makezine.com/2010/11/30/usbhacking/
The Arduino sketch is provided, so you should be able to try it out, however debugging the USB Host connection could get tricky real fast if it doesn't work out of the box.
I'm looking to control a mains powered light from a simple relay switch connected via USB to the computer.
The relay switch isn't even a USB device, it's just a simple switch that requires the USB voltage to turn it on. When the voltage drops below a threshold, the switch will turn the light off.
My problem is that I can't control the power output of a USB port. I'm happy to do it using any language on Windows or Linux (but preferably Java because I'm used to it).
Unfortunately, in most cases you cannot control the power supply to the USB port. The power supply is usually hardwired through, and not switchable in software. You can send a reset to a USB device, but that won't work in your case.
There are a number of projects on instructables that do similar to what you describe, but unfortunately they seem to either be quite complicated or require expensive parts.
EDIT: There is actually a product currently in the news which would do want you want, but it doesn't appear to be shipping yet: http://www.pwrusb.com/
EDIT (again): Apparently you can do this with some usb hubs. This post sugggests the Linksys USB2HUB4 is one that works.
EDIT (and again): Apparently there are a number of similar questions, but there don't seem to be any more useful answers:
https://stackoverflow.com/questions/405269/custom-usb-device-that-disables-power-to-usb-devices-plugged-into-it
Power off an USB device in software on Windows
Is there software or code to alter USB power output
Can I write a program that swiches USB on/off
Most of the USB to Serial or USB to RS232 $10 converters support hardware handshaking. Use one of those as a single channel digital io.
Connect your transistor that will drive the relay to DTR on the converter board and command DTR ON/OFF with the converters driver.
A 2N7002 is a good transistor to use (FET actually) since it will work from 3V and doesnt need any resistors anywhere.
Here is a complete solution.
It uses an Arduino board, with a USB connection, (and Uno for example) to control the relay and combines this with pfod (Protocol for Operation Discovery) www.pfod.com.au which will let you control the board/relay from either the Arduino IDE SerialMonitor, or a terminal window (TeraTerm) or a Java program. The message protocol encloses commands in { }, think simplified html for micros, and provides numerous screens, menus, sliders, text and numeric inputs, etc. A detailed protocol spec is available
See Garage Door Remote for a detailed example, with full Arduino code and an example of controlling the relay from TeraTerm as well as the Arduino IDE SerialMonitor.
There is also an Android app, pfodApp, which will do general purpose control via bluetooth, or wifi/internet with 128 bit security. The pfodApp does all the Android stuff, you only need to code some simple strings in your Arduino code to get any menu system you want. See www.pfod.com.au for numerous examples.
You need a USB-GPIO microcontroller:
Adafruit FT232H (about $15)
Arduino Nano ATmega328 (about $7)
See this answer
I would suggest placing a separate Raspberry Pi unit with a wake-on-lan feature activated so you can ping it off and on.
You could do it by combining these two products from Pololu, for about $25:
Micro Maestro (assembled)
Basic SPDT Relay Carrier with 5VDC Relay (Assembled)
The Maestro is mainly a servo controller but you can set any of its channels to be simple digital outputs instead. The output can be controlled from the Maestro Control Center software or you can write your own software. A digital output from a Maestro is suitable to turn on the relay on the relay carrier. The relay could be powered from USB through the Maestro; I think it draws about 100 mA of current so that probably will not be a problem for most USB ports, though it would not be USB-compliant because the total current drawn by the Maestro and the relay would be over 100 mA. You could supply your own power source for the relay if you are worried about that.