I want to define a Ring Group that, when called, rings one extension and one external number (mobile phone). What is the best way to achieve that?
Right now only the extension is called. So just entering an external number in the Destination field does not work, the logs say
[NOTICE] switch_cpp.cpp:1376 [ring groups][call forward all] user_exists id <mobileno> <domainname>
and later
[DEBUG] switch_ivr_originate.c:3865 Originate Resulted in Error Cause: 27 [DESTINATION_OUT_OF_ORDER]
It will check all calls using the dialplan to see if the destination is a local number for an external number it should say user_exists false every time.
This [DESTINATION_OUT_OF_ORDER] indicates that it may not have found a matching outbound route that matches the number of digits of the external phone number. Or it may mean that your carrier rejected the call maybe didn't like the caller ID that was sent. Easiest thing to try is attempt it with an outbound rout to different carrier.
In case you weren't aware FusionPBX 4.4 was release on 5 April 2018. Instructions to upgrade are post on docs.fusionpbx.com. Search term upgrade (version upgrade).
Related
I'm looking if there is a way to call the board (DSXLE5) and request info of the current KeyMapping value?
It is the first time I deal with DSX5 family, I've already identified that the firmware change process is different, as before, to change a DSXLE4 8 port card to be 2in + 6out we used
$mvConnectorConfig -2in6out -sn=XXXXX
and now I see that DSXLE5 needs to point the firmware (*.pin) with the load parameter.
$mvConnectorConfig load -f=xmio5_x2_00i12o.pin -sn=xxxxx
I see from the help that we can use -KeyMapping to change the boards, but how does it work and can we call the board to show which mapping is currently using?
I'm new here, so I'm sorry if it isn't 100% straight question.
Best Regards,
Rafael Girotto
I have 2 nodes of a cluster receiving messages from iothub. I split their responsibility by partition. Node 1 reads from partitions 1,3,5,7,9 and the other 2,4,6,8, and 0. Recently, my partition 8 stops responding until I stop my code and restart it. It seems like a device is sending a message that locks up the partition. What I want to do is list all devices in my partition 8. Is that possible? Is there a cloud shell command to get those devices in a list?
Not sure this will help you, but you can see the partition on the incoming messages. For example you could use Azure Stream Analytics to see the partitions using this query:
Select GetMetadataPropertyValue(IoTHub, '[IoTHub].[ConnectionDeviceId]') as DeviceId, partitionId
from IoTHub
Also, if you run locally in VisualStudio it will tell you which device is sending malformed JSON. eg.
[Warning] 10/21/2021 9:12:54 AM : User Warning Source 'IoTHub' had 1 occurrences of kind 'InputDeserializerError.InvalidData' between processing times '2021-10-21T15:12:50.5076449Z' and '2021-10-21T15:12:50.5712076Z'. Could not deserialize the input event(s) from resource 'Partition: [1], Offset: [455266583232], SequenceNumber: [634800], DeviceId: [DeviceName]' as Json. Some possible reasons: 1) Malformed events 2) Input source configured with incorrect serialization format
Also check your "Activity Log" blade in the ASA job. It may have more details for you.
I am stuck at a point where I am configuring the DCM module and the current parameter I am trying to configure DcmTimStrP2AdjustServer,
The requirement is P2CAN_SERVER_MAX = 25ms; P2STARCAN_SERVER_MAX = 5000ms;
Is DcmDspSessionP2ServerMax the same as P2CAN_SERVER_MAX? and if it is the same
What is the need for DcmTimStrP2AdjustServer and how do I find the best value for DcmTimStrP2AdjustServer.(The values all should be a multiple of DcmTaskTime which I find to be logical).
DcmTaskTime = 5ms;
I am following Autosar 4.0.3, using ETAS tool for configuring the parameters.
To fulfill your requirement, you need to configure respectively
DcmDspSessionP2ServerMax & DcmDspSessionP2StarServerMax for each session control in the DcmDspSessionRows at Dcm/DcmConfigSet/DcmDsp/DcmDspSession/.
i.e.
DcmDspSessionP2ServerMax 25
DcmDspSessionP2StarServerMax 5000
There is no DcmTimStrP2AdjustServer, but I guess you're referring to DcmTimStrP2ServerAdjust instead. DcmTimStrP2ServerAdjust & DcmTimStrP2StarServerAdjust should be configured to a multiple of your DcmTaskTime (5ms in your case, so i.e. 5ms, 10ms, 15, ms, ... is applicable) and are used to safeguard that the response is available on the bus before triggering the P2 or P2* timeouts. In your case you may want to set these values to the same values as in the DcmDspSessionRows if there is no other specification given, because the chosen timeout values there are already multiples of your DcmTaskTime:
DcmTimStrP2ServerAdjust 25
DcmTimStrP2StarServerAdjust 5000
The adjust value is an internal value, in order to adjust the delay between the Dcm Transmit Request and the message being actually on the Bus.
The definition of P2ServerMax and P2*ServerMax and their corresponding Adjust values is the same:
This parameter is used to guarantee that the diagnostic response is available on the bus before reaching P2 by adjusting the current DcmDspSessionP2ServerMax. This parameter mainly represents the software architecture dependent communication delay between the time the transmission is initiated by DCM and the time when the message is actually transmitted to the bus
Good day
I'm trying to perform load testing with LoadRunner 11. Here's an issue:
I've got automatically generated script after actions recording
Need to catch Session ID. I do it with web_reg_save_param() in the next way:
web_reg_save_param("S_ID",
"LB=Set-Cookie: JSESSIONID=",
"RB=; Path=/app/;",
LAST);
web_add_cookie("S_ID; DOMAIN={host}");
I catch ID from the response (Tree View):
D2B6F5B05A1366C395F8E86D8212F324
Compare it with Replay Log and see:
"S_ID = 75C78912AE78D26BDBDE73EBD9ADB510".
Compare 2 IDs above with the next request ID and see 3rd ID (Tree View):
80FE367101229FA34EB6429F4822E595
Why do I have 3 different IDs?
Let me know if I have to provide extra information.
You should Use(Search=All) below Code. Provided your Right and left boundary is correct:
web_reg_save_param("S_ID",
"LB=Set-Cookie: JSESSIONID=",
"RB=; Path=/app/;",
"Search=All",
LAST);
web_add_cookie("{S_ID}; DOMAIN={host}");
For Details refer HP Mannual for web_reg_save_param function.
I do not see what the conflict or controversy is here. Yes, items related to state or session will definitely change from user to user, one recording session to the next. They may even change from one request to the next. You may need to record several times to identify the change and use pattern for when you need to collect and when you need to reuse the collected data from a response in a subsequent request.
Take a listen to this podcast. It should help
http://www.perfbytes.com/dynamic-data-correlation
In beanstalkd
telnet localhost 11300
USING foo
put 0 100 120 5
hello
INSERTED 1
How can I know what is the priority of this job when I reserve it? And can I release it by making the new priority equals to current priority +100?
Beanstalkd doesn't return the priority with the data - but you could easily add it as metadata in your own message body. for example, with Json as a message wrapper:
{'priority':100,'timestamp':1302642381,'job':'download http://example.com/'}
The next message that will be reserved will be the next available entry from the selected tubes, according to priority and time - subject to any delay that you had requested when you originally sent the message to the queue.
Addition: You can get the priority of a beanstalk job (as well as a number of other pieces of information, such as how many times it has previously been reserved), but it's an additional call - to the stats-job command. Called with the jobId, it returns about a dozen different pieces of information. See the protocol document, and your libraries docs.